FireCADCalc

Helical Torsion Spring Rate and Stress

Angular rate, deflection and bending stress of a helical torsion spring from wire and coil diameters, active turns and moment, with the curvature factor.

Inputs

Examples: 3 mm music wire, 25 mm coil, 6 turns, 2 N·m1.5 mm, 12 mm, 10 turns, 0.2 N·m5 mm, 50 mm, 4.5 turns, 8 N·m

Results

Theoretical rate; friction between coils and over the arbor lowers it slightly (Shigley's empirical 10.8 instead of 64/(2π) = 10.2).

Rate (moment per radian)0.12953N·m
Rate (moment per turn)0.81385N·m
Angular deflection under the moment88.468°
Curvature factor (inner fibre)1.1027
Bending stress K_i 32 M/(π d³)665.59MPa

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: 3 mm music wire, 25 mm coil, 6 turns, 2 N·m. The inputs, in the units selected above:

InputValue
Wire diameter3.0000 mm
Mean coil diameter25.000 mm
Active turns (body turns + end-leg equivalent)6.0000 -
Modulus of the wire196.50 GPa
Applied moment2.0000 N·m

Applying the formula below gives:

ResultValue
Rate (moment per radian)1.6580 N·m
Rate (moment per turn)10.417 N·m
Angular deflection under the moment69.116 °
Curvature factor (inner fibre)1.0982
Bending stress K_i 32 M/(π d³)828.59 MPa

Open this example in the calculator and change any input.

Formula

\(k = \frac{d^4 E}{64 D N_a}, \quad K_i = \frac{4C^2 - C - 1}{4C(C - 1)}, \quad \sigma = K_i\, \frac{32 M}{\pi d^3}, \quad C = \frac{D}{d}\)

Variables

Symbol Meaning SI unit
\(d\) Wire diameter m
\(D\) Mean coil diameter m
\(N_a\) Active turns (body turns + end-leg equivalent) -
\(E\) Modulus of the wire Pa
\(M\) Applied moment N·m
\(k\) Rate (moment per radian) N·m
\(k'\) Rate (moment per turn) N·m
\(\theta\) Angular deflection under the moment rad
\(K_i\) Curvature factor (inner fibre) -
\(\sigma\) Bending stress K_i 32 M/(π d³) Pa

Method and standards

Bending of the coiled wire.

Where it is used

  • Hinges, latches and return springs.
  • Spring selection.

Common mistakes

  • Torsion stress formula from compression springs.
  • Forgetting leg contribution to turns.

Assumptions and limits

  • The rate is the theoretical d⁴E/(64 D N_a). Shigley notes that coil friction makes measured rates a little lower and gives an empirical form with 10.8 in place of 64/(2π) = 10.19 per turn, about 6 % softer; use it when matching test data.

  • Round wire, close-wound.

References

  • Shigley's Mechanical Engineering Design (Budynas and Nisbett)
  • ch. 10 (helical torsion springs, k = d⁴E/(64 D N_a), K_i)

Questions and answers

A 3 mm wire, 25 mm coil, 6 turns, music wire?

Rate 1.6580 N·m/rad (10.417 N·m per turn).

Why does the coil diameter shrink under load?

Winding up tightens the coil; leave clearance over the arbor.

Which stress governs?

Bending at the inner fibre, raised by K_i.

Method and article reviewed by FireCAD engineering on 12 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.