Worked example
Example: 30 kW at 1 450 rpm, 150 N·m bending, 40 MPa, Km 1.5. The inputs, in the units selected above:
| Input | Value |
|---|---|
| Power transmitted | 30.000 kW |
| Shaft speed | 1,450.0 rpm |
| Bending moment at the section | 150.00 N·m |
| Allowable shear stress | 40.000 MPa |
| Shock and fatigue factor for bending | 1.5000 - |
| Shock and fatigue factor for torsion | 1.0000 - |
| Bore ratio of a hollow shaft d_i/d_o (0 = solid) | 0 % |
Applying the formula below gives:
| Result | Value |
|---|---|
| Torque transmitted | 197.57 N·m |
| Equivalent torque | 299.43 N·m |
| Shaft diameter (outside) | 33.657 mm |
| Bore diameter (hollow shaft) | 0 mm |
Open this example in the calculator and change any input.
Formula
\(T = \frac{P}{2 \pi n}\)
\(T_e = \sqrt{(K_m M)^2 + (K_t T)^2}\)
\(d_o = \left[\frac{16 T_e}{\pi \tau_a (1 - k^4)}\right]^{1/3}, \quad d_i = k\, d_o\)
Variables
| Symbol | Meaning | SI unit |
|---|---|---|
| \(P\) | power | W |
| \(n\) | speed | rev/s |
| \(M\) | bending moment | N·m |
| \(\tau_a\) | allowable shear stress | Pa |
| \(K_m\) | bending shock and fatigue factor | - |
| \(K_t\) | torsion shock and fatigue factor | - |
| \(k\) | bore ratio d_i/d_o | - |
| \(T\) | torque | N·m |
| \(T_e\) | equivalent torque | N·m |
| \(d_o\) | outside diameter | m |
| \(d_i\) | bore diameter | m |
Method and standards
Maximum shear stress theory for a shaft under bending and torsion: the equivalent torque with shock and fatigue factors gives the diameter at the allowable shear stress.
Where it is used
- Sizing pump, fan and conveyor shafts.
- Checking an existing shaft for a power increase.
- Comparing solid and hollow shafts.
Common mistakes
- Ignoring bending from belt pull or overhung loads.
- Using yield strength directly as the allowable stress.
- Forgetting the keyway and critical speed.
Assumptions and limits
- Static strength; deflection, critical speed and detailed fatigue to be checked separately.
- The factor of safety is inside the allowable shear stress you enter. K_m and K_t are your inputs: machine design texts tabulate the ASME code values for transmission shafting (for a rotating shaft with gradually applied load, K_m = 1.5 and K_t = 1.0; higher for shock loads).
References
- Maximum shear stress (Tresca) theory with shock and fatigue factors
Questions and answers
What shaft for 30 kW at 1 450 rpm with 150 N·m bending?
About 34 mm solid at 40 MPa allowable shear with Km 1.5; round up to a standard size and check keyway and deflection.
What is equivalent torque?
√((Km M)² + (Kt T)²): the single torque that gives the same maximum shear stress as the combined bending and twisting.
Why is a hollow shaft lighter?
The centre carries little stress; a bore of 0.6 D adds only about 5 % to the outside diameter for the same strength.
Method and article reviewed by FireCAD engineering on 12 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.