FireCADCalc

Journal Bearing Friction by Petroff's Equation

Friction torque, friction coefficient and power loss of a lightly loaded journal bearing by Petroff's equation, with the bearing pressure.

Inputs

Examples: 30 mPa·s, 1 500 rpm, 50 mm journal, 50 mm long, 40 µm10 mPa·s, 3 000 rpm, 80 mm, 60 mm, 60 µm100 mPa·s, 300 rpm, 200 mm, 150 mm, 150 µm

Results

Petroff's equation assumes a concentric journal (light load); under real loads the journal runs eccentric and friction is higher.

Friction torque 4π² μ N r³ l / c0.57830N·m
Friction coefficient T/(W r)0.011566
Power lost90.839W
Bearing pressure W/(2 r l)800.00kPa

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: 30 mPa·s, 1 500 rpm, 50 mm journal, 50 mm long, 40 µm. The inputs, in the units selected above:

InputValue
Oil viscosity at the running temperature30.000 mPa·s
Journal speed1,500.0 rpm
Journal radius25.000 mm
Bearing length50.000 mm
Radial clearance40.000 µm
Radial load2.0000 kN

Applying the formula below gives:

ResultValue
Friction torque 4π² μ N r³ l / c0.57830 N·m
Friction coefficient T/(W r)0.011566
Power lost90.839 W
Bearing pressure W/(2 r l)800.00 kPa

Open this example in the calculator and change any input.

Formula

\(T = \frac{4\pi^2 \mu N r^3 l}{c}, \quad f = \frac{T}{W r}, \quad P = 2\pi N T\)

Variables

Symbol Meaning SI unit
\(\mu\) Oil viscosity at the running temperature Pa·s
\(N\) Journal speed 1/s
\(r\) Journal radius m
\(l\) Bearing length m
\(c\) Radial clearance m
\(W\) Radial load N
\(T\) Friction torque 4π² μ N r³ l / c N·m
\(f\) Friction coefficient T/(W r) -
\(P\) Power lost W
\(p\) Bearing pressure W/(2 r l) Pa

Method and standards

Viscous shear in a concentric film.

Where it is used

  • Bearing heat and oil flow estimates.
  • Machine design examinations.

Common mistakes

  • Diameter instead of radius.
  • Viscosity at the wrong temperature.

Assumptions and limits

  • Concentric journal, full film. Valid for lightly loaded bearings only: check the Sommerfeld number S = (r/c)² μN/p; for loaded bearings use the Raimondi–Boyd charts, which give a higher friction.

References

  • N. Petroff (1883); Shigley's Mechanical Engineering Design (Budynas and Nisbett)
  • ch. 12

Questions and answers

50 mm journal, 50 mm long, 40 µm clearance, 30 mPa·s oil, 1500 rpm?

Torque 0.578 N·m, loss 91 W.

Why does clearance matter?

Friction rises as clearance falls; too much clearance lowers load capacity.

What viscosity?

At the oil film temperature, much lower than at 40 °C.

Method and article reviewed by FireCAD engineering on 12 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.