FireCADCalc

Laminated (Leaf) Spring: Stress and Deflection

Bending stress and deflection of a semi-elliptic laminated leaf spring from load, span, leaf width and thickness and the number of full-length and graduated leaves.

Thermal power plantProcess steam and utilitiesSugar mill and cogenerationChemical and fertiliserPulp and paperFood, dairy and textile

Inputs

Examples: 1 m span, 2 + 8 leaves 60 × 10 mm, 20 kNTrailer spring 1.2 m, 1 + 8 leaves 75 × 12 mm, 25 kN

Results

Semi-elliptic spring treated as two cantilevers of length L each carrying W/2, with full-length leaves pre-stressed (nipped) so all leaves reach the same stress. Ignores leaf friction.

Bending stress (pre-stressed, equalised)500.00MPa
Deflection at the centre54.897mm
Spring rate364.32kN/m

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: 1 m span, 2 + 8 leaves 60 × 10 mm, 20 kN. The inputs, in the units selected above:

InputValue
Load at the centre20.000 kN
Span (eye to eye)1,000.0 mm
Leaf width60.000 mm
Leaf thickness10.000 mm
Full-length leaves2.0000 -
Graduated leaves8.0000 -
Elastic modulus207.00 GPa

Applying the formula below gives:

ResultValue
Bending stress (pre-stressed, equalised)500.00 MPa
Deflection at the centre54.897 mm
Spring rate364.32 kN/m

Open this example in the calculator and change any input.

Formula

\(\sigma = \frac{6(W/2)L}{nbt^2} = \frac{3WL}{nbt^2}, \quad \delta = \frac{12(W/2)L^3}{Ebt^3(2n_g + 3n_f)} = \frac{6WL^3}{Ebt^3(2n_g + 3n_f)}\ \ (W\text{ centre load, }L\text{ half span}, n = n_f + n_g)\)

Variables

Symbol Meaning SI unit
\(W\) Load at the centre N
\(2L\) Span (eye to eye) m
\(b\) Leaf width m
\(t\) Leaf thickness m
\(n_f\) Full-length leaves -
\(n_g\) Graduated leaves -
\(E\) Elastic modulus Pa
\(\sigma\) Bending stress (pre-stressed, equalised) Pa
\(\delta\) Deflection at the centre m
\(k\) Spring rate N/m

Method and standards

Multi-leaf spring theory.

Where it is used

  • Vehicle and trailer suspensions.
  • Machine supports.

Common mistakes

  • Using full span for L.
  • Ignoring leaf friction (damping).

Assumptions and limits

  • Equal width and thickness leaves; pre-stressed.
  • The stress is not compared with an allowable, and no ineffective length is deducted for the centre clip or band (deduct it from the span yourself).

References

  • Bhandari
  • Design of Machine Elements
  • 4th ed.
  • ch. 10 (multi-leaf springs: σ = 6WL/(nbt²), δ = 12WL³/(Ebt³(2n_g + 3n_f)))

Questions and answers

Why graduated leaves?

They approximate a beam of uniform strength, so material is used efficiently along the spring.

What is nipping?

Giving full-length leaves extra curvature so that, under load, all leaves end up at the same stress.

What do the defaults represent?

A 1 m semi-elliptic spring with 2 full and 8 graduated 60 × 10 mm leaves carrying 20 kN.

Method and article reviewed by FireCAD engineering on 13 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.