FireCADCalc

Shaft Key Shear and Crushing Stress (Key Length)

Shear and crushing (bearing) stresses in a parallel or sunk shaft key from the torque, and the key length needed for allowable stresses in shear and crushing.

PumpElectric motor

Inputs

Examples: 1 kN·m on a 50 mm shaft, 14 x 9 x 60 mm key3 kN·m, 75 mm, 20 x 12 x 100 mm250 N·m, 30 mm, 8 x 7 x 40 mm

Results

The key entered is shorter than the length needed: it is overstressed in shear or crushing.

Half the key height bears on the hub (sunk key). Stress concentration and fatigue are not included.

Tangential force at the shaft surface 2T / d40.000kN
Shear stress in the key F / (b l)47.619MPa
Crushing stress F / (h l / 2)148.15MPa
Length needed for shear47.619mm
Length needed for crushing88.889mm
Key length needed (larger of the two)88.889mm

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: 1 kN·m on a 50 mm shaft, 14 x 9 x 60 mm key. The inputs, in the units selected above:

InputValue
Torque transmitted1,000.0 N·m
Shaft diameter50.000 mm
Key width14.000 mm
Key height9.0000 mm
Key length60.000 mm
Allowable shear stress of the key60.000 MPa
Allowable crushing stress100.00 MPa

Applying the formula below gives:

ResultValue
Tangential force at the shaft surface 2T / d40.000 kN
Shear stress in the key F / (b l)47.619 MPa
Crushing stress F / (h l / 2)148.15 MPa
Length needed for shear47.619 mm
Length needed for crushing88.889 mm
Key length needed (larger of the two)88.889 mm

Open this example in the calculator and change any input.

Formula

\(F = \frac{2T}{d}, \quad \tau = \frac{F}{b\,l}, \quad \sigma_c = \frac{F}{(h/2)\,l}\)

\(l = \max\left(\frac{F}{b\,\tau_a},\ \frac{2F}{h\,\sigma_{c,a}}\right)\)

Variables

Symbol Meaning SI unit
\(T\) Torque transmitted N·m
\(d\) Shaft diameter m
\(b\) Key width m
\(h\) Key height m
\(l\) Key length m
\(\tau_a\) Allowable shear stress of the key Pa
\(\sigma_{c,a}\) Allowable crushing stress Pa
\(F\) Tangential force at the shaft surface 2T / d N
\(\tau\) Shear stress in the key F / (b l) Pa
\(\sigma_c\) Crushing stress F / (h l / 2) Pa
\(l_s\) Length needed for shear m
\(l_c\) Length needed for crushing m
\(l_{req}\) Key length needed (larger of the two) m

Method and standards

Force at the shaft surface sheared across the key width and pressed against half its height.

Where it is used

  • Couplings, pulleys, gears and impellers.
  • Checking a key after a motor upgrade.
  • Machine design examinations.

Common mistakes

  • Using radius instead of diameter.
  • Using full key height for crushing.
  • Ignoring the hub material's lower crushing strength.

Assumptions and limits

  • Uniform pressure; no fatigue or stress concentration. A key shorter than the length needed is flagged.

References

  • Shigley's Mechanical Engineering Design
  • ch. 7 (keys)
  • V.B. Bhandari
  • Design of Machine Elements
  • ch. 9

Questions and answers

Is a 14 × 9 × 60 mm key enough for 1 kN·m on a 50 mm shaft?

The force is 40 kN; shear 47.6 MPa is fine, but crushing 148 MPa exceeds 100 MPa. It needs 89 mm length.

Why half the key height?

A sunk key sits half in the shaft and half in the hub, so the crushing area is h/2 × l.

Which governs?

Usually crushing for square-ish keys; the calculator shows both lengths.

Method and article reviewed by FireCAD engineering on 12 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.