Worked example
Example: M12 coarse, pitch 1.75 mm. The inputs, in the units selected above:
| Input | Value |
|---|---|
| Nominal (major) diameter | 12.000 mm |
| Thread pitch | 1.7500 mm |
Applying the formula below gives:
| Result | Value |
|---|---|
| Tensile stress area | 84.267 mm² |
| Pitch diameter | 10.863 mm |
| Minor diameter of the bolt thread | 9.8530 mm |
| Stress diameter (d₂ + d₃)/2 | 10.358 mm |
| Area at the minor diameter | 76.247 mm² |
Open this example in the calculator and change any input.
Formula
\(A_s = \frac{\pi}{4}\left(\frac{d_2 + d_3}{2}\right)^2 = \frac{\pi}{4}\,(d - 0.938\,194\,P)^2\)
\(d_2 = d - \tfrac{3\sqrt{3}}{8}P, \quad d_3 = d - \tfrac{17\sqrt{3}}{24}P\)
\(A_3 = \frac{\pi}{4} d_3^2\)
Variables
| Symbol | Meaning | SI unit |
|---|---|---|
| \(d\) | nominal (major) diameter | m |
| \(P\) | thread pitch | m |
| \(d_2\) | pitch diameter | m |
| \(d_3\) | minor diameter of the bolt (external) thread | m |
| \(d_s\) | stress diameter, mean of d_2 and d_3 | m |
| \(A_s\) | tensile stress area | m² |
| \(A_3\) | area at the minor diameter | m² |
Method and standards
The ISO metric thread is built on a triangle of height H = (√3/2) P (ISO 68-1). The pitch diameter is d − 2·(3/8)H and the minor diameter of the bolt thread is d − 2·(17/24)H (ISO 724). ISO 898-1 defines the tensile stress area as the circle on the mean of these two diameters. The proof load of a bolt is its proof stress times this area; continue to the bolt torque calculator for preload and torque.
Where it is used
- Finding the proof load and preload of a bolt for a torque calculation.
- Checking bolt stress under a known load on a flange, bracket or foundation bolt.
- Comparing coarse and fine pitches for the same diameter.
Common mistakes
- Using the shank area: it overstates the strength of the thread by 20–30 %.
- Using the minor-diameter area as the stress area: it is about 8 % low.
- Using this for inch (UNC/UNF) threads: their stress area is defined differently.
Assumptions and limits
- ISO metric (60°) threads only, coarse or fine pitch.
- Basic dimensions; manufacturing tolerances on the thread are not included.
- Gives the area only; the bolt's proof and tensile strengths come from its property class.
References
- ISO 898-1 stress area definition
- ISO 68-1 / ISO 724 thread profile
Questions and answers
What is the stress area of an M20 × 2.5 bolt?
245 mm². An M12 × 1.75 is 84.3 mm² and an M30 × 3.5 is 561 mm².
Why not use the full shank area?
A bolt breaks in the thread. The stress area, between the pitch and minor diameters, is the area that tensile tests of threaded bolts fit best.
Does a fine thread have more stress area?
Yes. A finer pitch cuts less deep, so an M20 × 1.5 has more stress area than an M20 × 2.5.
Method and article reviewed by FireCAD engineering on 12 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.