Worked example
Example: 22 kW at 1,450 rpm, 200 mm, 6 kW per belt. The inputs, in the units selected above:
| Input | Value |
|---|---|
| Transmitted power | 22.000 kW |
| Service factor | 1.3000 - |
| Rated power per belt (maker's data at this speed and diameter) | 6.0000 kW |
| Driver pulley pitch diameter | 200.00 mm |
| Driver speed | 1,450.0 rpm |
| Belt mass per metre | 0.19000 kg/m |
| Belt–groove friction coefficient | 0.30000 - |
| Groove angle | 40.000 ° |
| Wrap angle on the small pulley | 160.43 ° |
Applying the formula below gives:
| Result | Value |
|---|---|
| Belt speed | 15.184 m/s |
| Number of belts | 5.0000 |
| Centrifugal tension per belt | 43.807 N |
| Tight-side tension per belt | 455.86 N |
| Slack-side tension per belt | 79.152 N |
Open this example in the calculator and change any input.
Formula
\(n = \left\lceil\frac{K_sP}{P_b}\right\rceil, \quad T_c = m_bv^2, \quad \frac{T_1 - T_c}{T_2 - T_c} = e^{\mu\theta/\sin\beta}\)
Variables
| Symbol | Meaning | SI unit |
|---|---|---|
| \(P\) | Transmitted power | W |
| \(K_s\) | Service factor | - |
| \(P_b\) | Rated power per belt (maker's data at this speed and diameter) | W |
| \(d\) | Driver pulley pitch diameter | m |
| \(N\) | Driver speed | 1/s |
| \(m_b\) | Belt mass per metre | kg/m |
| \(\mu\) | Belt–groove friction coefficient | - |
| \(2\beta\) | Groove angle | rad |
| \(\theta\) | Wrap angle on the small pulley | rad |
| \(v\) | Belt speed | m/s |
| \(n\) | Number of belts | - |
| \(T_c\) | Centrifugal tension per belt | N |
| \(T_1\) | Tight-side tension per belt | N |
| \(T_2\) | Slack-side tension per belt | N |
Method and standards
Belt mechanics.
Where it is used
- Fan, pump and compressor belt drives.
- Belt replacement and retensioning.
Common mistakes
- Using flat-belt friction for V-belts.
- Ignoring the service factor.
Assumptions and limits
The rated power per belt is entered as the maker gives it; arc-of-contact and belt-length correction factors must be applied to it before entry. The page warns above about 30 m/s belt speed.
Belt at the point of slip at design load.
References
- Budynas and Nisbett
- Shigley's Mechanical Engineering Design
- 10th ed. (McGraw-Hill, 2015)
- ch. 17 (V-belts: tension ratio e^(μθ/sin β), centrifugal tension)
Questions and answers
Why does the groove raise grip?
The V wedges the belt; effective friction becomes μ/sin β, about three times the flat-belt value.
Why does centrifugal tension matter?
At high belt speed it uses up belt strength without transmitting power; above about 30 m/s V-belts lose capacity fast.
What do the defaults represent?
A 22 kW, 1,450 rpm drive on a 200 mm pulley with B-section-like belts rated 6 kW each.
Method and article reviewed by FireCAD engineering on 13 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.