FireCADCalc

Spur Gear Geometry: Module, Pitch Diameter, Centre Distance

Pitch, tip and root diameters, circular pitch, centre distance and speed ratio of a pair of standard involute spur gears from the module and tooth numbers.

Inputs

Examples: Module 4, 20 and 60 teeth, 20°Module 2.5, 17 and 45 teeth, 20°Module 10, 25 and 100 teeth, 25°

Results

Standard full-depth teeth: addendum 1 m, dedendum 1.25 m, no profile shift.

Pitch diameter of the pinion m z₁80.000mm
Pitch diameter of the gear240.00mm
Centre distance (d₁ + d₂)/2160.00mm
Tip diameter of the pinion (addendum m)88.000mm
Root diameter of the pinion (dedendum 1.25 m)70.000mm
Base circle diameter of the pinion75.175mm
Circular pitch π m12.566mm
Speed ratio z₂/z₁3.0000

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: Module 4, 20 and 60 teeth, 20°. The inputs, in the units selected above:

InputValue
Module4.0000 mm
Teeth on the pinion20.000 -
Teeth on the gear60.000 -
Pressure angle20.000 °

Applying the formula below gives:

ResultValue
Pitch diameter of the pinion m z₁80.000 mm
Pitch diameter of the gear240.00 mm
Centre distance (d₁ + d₂)/2160.00 mm
Tip diameter of the pinion (addendum m)88.000 mm
Root diameter of the pinion (dedendum 1.25 m)70.000 mm
Base circle diameter of the pinion75.175 mm
Circular pitch π m12.566 mm
Speed ratio z₂/z₁3.0000

Open this example in the calculator and change any input.

Formula

\(d = m z, \quad a = \frac{m (z_1 + z_2)}{2}, \quad d_a = d + 2m, \quad d_f = d - 2.5m, \quad d_b = d \cos\phi\)

Variables

Symbol Meaning SI unit
\(m\) Module m
\(z_1\) Teeth on the pinion -
\(z_2\) Teeth on the gear -
\(\phi\) Pressure angle rad
\(d_1\) Pitch diameter of the pinion m z₁ m
\(d_2\) Pitch diameter of the gear m
\(a\) Centre distance (d₁ + d₂)/2 m
\(d_{a1}\) Tip diameter of the pinion (addendum m) m
\(d_{f1}\) Root diameter of the pinion (dedendum 1.25 m) m
\(d_{b1}\) Base circle diameter of the pinion m
\(p\) Circular pitch π m m
\(i\) Speed ratio z₂/z₁ -

Method and standards

Standard involute gear geometry.

Where it is used

  • Gearbox layout.
  • Replacing a worn gear.

Common mistakes

  • Mixing module and diametral pitch.
  • Ignoring undercut.

Assumptions and limits

  • Standard teeth, no profile shift.

References

  • ISO 53 / ISO 54 standard basic rack (addendum m, dedendum 1.25 m)
  • Shigley's Mechanical Engineering Design (Budynas and Nisbett)
  • ch. 13

Questions and answers

A 4 mm module, 20 and 60 teeth: what centre distance?

Pitch diameters 80 and 240 mm, centre distance 160 mm, ratio 3.

What is the module?

Pitch diameter divided by the number of teeth, in mm.

Why avoid very small pinions?

Below about 17 teeth at 20° the cutter undercuts the tooth root.

Method and article reviewed by FireCAD engineering on 12 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.