FireCADCalc

Fillet and Butt Weld Strength

Allowable load of a fillet weld (throat 0.707 s) in shear or a butt weld in tension from size, length and allowable stress, with the weld length needed.

Inputs

Examples: 8 mm fillet, 200 mm, 94 MPa; 100 kN12 mm butt weld, 150 mm, 140 MPa; 200 kN6 mm fillet, two runs of 120 mm, 94 MPa; 60 kN

From your design code or specification for the weld metal and loading.

Results

Throat of an equal-leg fillet is s cos 45° = 0.707 s. Allowable stresses and length deductions for weld ends follow your design code.

Throat thickness5.6569mm
Throat area1,131.4mm²
Allowable load106.35kN
Stress under the applied load88.388MPa
Weld length needed for the applied load188.06mm

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: 8 mm fillet, 200 mm, 94 MPa; 100 kN. The inputs, in the units selected above:

InputValue
Weld typeFillet weld, shear on the throat
Fillet leg size, or plate thickness for a butt weld8.0000 mm
Effective weld length200.00 mm
Allowable stress on the throat or section94.000 MPa
Applied load (to find the length needed)100.00 kN

Applying the formula below gives:

ResultValue
Throat thickness5.6569 mm
Throat area1,131.4 mm²
Allowable load106.35 kN
Stress under the applied load88.388 MPa
Weld length needed for the applied load188.06 mm

Open this example in the calculator and change any input.

Formula

\(t = 0.707\, s\ (\text{fillet}), \quad F_a = t\, L\, \tau_a, \quad L_{req} = \frac{F}{t\, \tau_a}\)

Variables

Symbol Meaning SI unit
\(\text{weld}\) Weld type -
\(s\) Fillet leg size, or plate thickness for a butt weld m
\(L\) Effective weld length m
\(\tau_a\) Allowable stress on the throat or section Pa
\(F\) Applied load (to find the length needed) N
\(t\) Throat thickness m
\(A\) Throat area m²
\(F_a\) Allowable load N
\(\tau\) Stress under the applied load Pa
\(L_{req}\) Weld length needed for the applied load m

Method and standards

Throat area method.

Where it is used

  • Brackets, lugs and frames.
  • Fabrication checks.

Common mistakes

  • Leg size as throat.
  • No allowance for start and stop craters.

Assumptions and limits

  • Straight weld under a direct load through the weld group's centroid. Eccentric loads (bending or torsion on the weld group) are not covered, and no length is deducted for start and end craters or returns; apply your code's allowable stress and deductions.

  • Static load, equal-leg fillet.

References

  • Throat-area method (Shigley's Mechanical Engineering Design (Budynas and Nisbett), ch. 9; AWS and IS 816 use the same throat definition)

Questions and answers

What does an 8 mm fillet 200 mm long carry at 94 MPa on the throat?

Throat 5.66 mm, 106 kN.

Why 0.707?

The throat of a 45° fillet is the leg × cos 45°.

Two welds?

Enter the total length of both.

Method and article reviewed by FireCAD engineering on 12 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.