FireCADCalc

Slider–Crank: Piston Displacement, Velocity and Acceleration

Piston displacement, velocity and acceleration of a slider–crank at a crank angle from crank radius, rod length and speed, with mean piston speed.

Thermal power plantProcess steam and utilitiesSugar mill and cogenerationChemical and fertiliserPulp and paperFood, dairy and textile

Inputs

Examples: 50/200 mm at 1,500 rpm, 45°Compressor 75/300 mm at 750 rpm, 120°

Results

Exact relations; the common approximations v ≈ rω(sin θ + sin 2θ/2n) and a ≈ rω²(cos θ + cos 2θ/n) are close for n = l/r above about 3.5. The acceleration here is in m/s².

Piston displacement from inner dead centre17.795mm
Piston velocity6.5511m/s
Piston acceleration (m/s²)877.41
Mean piston speed5.0000m/s
Connecting rod angle10.182°

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: 50/200 mm at 1,500 rpm, 45°. The inputs, in the units selected above:

InputValue
Crank radius50.000 mm
Connecting rod length200.00 mm
Crank speed1,500.0 rpm
Crank angle from inner dead centre45.000 °

Applying the formula below gives:

ResultValue
Piston displacement from inner dead centre17.794 mm
Piston velocity6.5511 m/s
Piston acceleration (m/s²)877.41
Mean piston speed5.0000 m/s
Connecting rod angle10.182 °

Open this example in the calculator and change any input.

Formula

\(x = r(1 - \cos\theta) + l - \sqrt{l^2 - r^2\sin^2\theta}, \quad v = r\omega\left(\sin\theta + \frac{\sin\theta\cos\theta}{\sqrt{n^2 - \sin^2\theta}}\right)\)

\(a = r\omega^2\left(\cos\theta + \frac{n^2\cos 2\theta + \sin^4\theta}{(n^2 - \sin^2\theta)^{3/2}}\right), \quad \bar v = 4rN, \quad \sin\phi = \frac{\sin\theta}{n}, \quad \omega = 2\pi N,\ n = \frac{l}{r}\)

Variables

Symbol Meaning SI unit
\(r\) Crank radius m
\(l\) Connecting rod length m
\(N\) Crank speed 1/s
\(\theta\) Crank angle from inner dead centre rad
\(x\) Piston displacement from inner dead centre m
\(v\) Piston velocity m/s
\(a\) Piston acceleration m/s²
\(\omega\) Crank angular speed 2πN rad/s
\(n\) Rod ratio l/r -
\(\bar v\) Mean piston speed m/s
\(\phi\) Connecting rod angle rad

Method and standards

Exact slider–crank relations.

Where it is used

  • Reciprocating compressor and pump design.
  • Engine dynamics and inertia forces.

Common mistakes

  • Measuring angle from bottom dead centre.
  • Using the approximation for short rods.

Assumptions and limits

  • Rigid links; constant crank speed.
  • The acceleration is given in m/s² in every unit system.

References

  • Rattan
  • Theory of Machines
  • 4th ed. (McGraw-Hill, 2014); Bhandari
  • Design of Machine Elements
  • 4th ed. (McGraw-Hill, 2017) (slider–crank: exact displacement, velocity and acceleration)

Questions and answers

Why is piston acceleration largest at top dead centre?

The crank and rod angularities add there; at bottom dead centre they partly cancel.

What is the rod ratio?

l/r, usually 3.5–4.5 in engines and compressors; shorter rods raise secondary forces.

What do the defaults represent?

A 50 mm crank and 200 mm rod at 1,500 rpm, 45° past inner dead centre.

Method and article reviewed by FireCAD engineering on 13 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.