FireCADCalc

Belt Length, Wrap Angle and Pulley Speed

Length of an open or crossed belt from pulley diameters and centre distance, with the wrap angle on the small pulley, belt speed and driven speed.

PumpFan and blowerElectric motor

Inputs

Examples: Open: 400 and 160 mm, 800 mm centres, 1450 rpmOpen: 250 and 100 mm, 500 mm, 2900 rpmCrossed: 300 and 150 mm, 1 m, 960 rpm

Results

Belt pitch length1,561.0mm
Wrap angle on the small pulley162.75°
Belt speed15.184m/s
Speed of the large pulley (no slip)1,160.0rpm

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: Open: 400 and 160 mm, 800 mm centres, 1450 rpm. The inputs, in the units selected above:

InputValue
Large pulley diameter (pitch)400.00 mm
Small pulley diameter (pitch)160.00 mm
Centre distance800.00 mm
Belt driveOpen belt
Speed of the small (driving) pulley1,450.0 rpm

Applying the formula below gives:

ResultValue
Belt pitch length2,497.6 mm
Wrap angle on the small pulley162.75 °
Belt speed12.147 m/s
Speed of the large pulley (no slip)580.00 rpm

Open this example in the calculator and change any input.

Formula

\(L = 2C + \frac{\pi (D + d)}{2} + \frac{(D \mp d)^2}{4C} \qquad \theta = \pi \mp 2\arcsin\frac{D \mp d}{2C} \qquad v = \pi d\,n_1 \qquad n_2 = n_1\frac{d}{D}\)

Variables

Symbol Meaning SI unit
\(D\) large pulley pitch diameter m
\(d\) small pulley pitch diameter m
\(C\) centre distance m
\(\text{drive}\) open or crossed –
\(n_1\) small pulley speed rev/s
\(L\) belt pitch length m
\(\theta\) wrap angle on small pulley rad
\(v\) belt speed m/s
\(n_2\) large pulley speed rev/s

Method and standards

Exact geometry of the open belt with the usual series approximation for length (upper signs open, lower signs crossed for the bracketed terms).

Where it is used

  • Fan and pump belt drives.
  • Changing fan speed by pulley.
  • Replacement belt selection.

Common mistakes

  • Using outside diameters.
  • Forgetting slip (1–2 %).
  • Too short a centre distance.

Assumptions and limits

  • Rigid inextensible belt; no slip.
  • The length uses the series approximation; when it differs from the exact L = 2C cos α + π(D+d)/2 + α(D−d) (open belt) by more than 0.5 % the exact length is given in a note.

References

  • Belt drive geometry

Questions and answers

What belt fits 400 and 160 mm pulleys at 800 mm centres?

2.498 m pitch length; wrap on the small pulley 162.7°; at 1450 rpm the belt runs at 12.2 m/s and the large pulley turns at 580 rpm.

Why check wrap angle?

Below about 120° V-belts slip; increase the centre distance or add an idler.

Pitch or outside diameter?

Pitch diameters; take them from the pulley catalogue.

Method and article reviewed by FireCAD engineering on 12 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.