FireCADCalc

Rolling Bearing L10 Life from Load Rating

Basic rating life L10 of a ball or roller bearing in millions of revolutions and in hours, from its dynamic load rating, the equivalent load and the speed.

PumpFan and blowerElectric motor

Inputs

Examples: 6308 ball bearing 30.7 kN at 4 kN, 1 450 rpmRoller bearing 140 kN at 18 kN, 980 rpmBall 14 kN at 2.5 kN, 2 900 rpm, a1 0.64

Take the value for your reliability from the bearing maker's catalogue.

Results

Basic life only: lubrication, contamination and fatigue-limit effects (the a_ISO factor) come from the maker's method.

Load ratio5.6000
Rating life, millions of revolutions112.39
Rating life in operating hours645.94h

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: 6308 ball bearing 30.7 kN at 4 kN, 1 450 rpm. The inputs, in the units selected above:

InputValue
Bearing typeBall bearing (p = 3)
Basic dynamic load rating (catalogue)30.700 kN
Equivalent dynamic load4.0000 kN
Speed1,450.0 rpm
Life factor for reliability (1 for 90 %)1.0000 -

Applying the formula below gives:

ResultValue
Load ratio7.6750
Rating life, millions of revolutions452.10
Rating life in operating hours5,196.6 h

Open this example in the calculator and change any input.

Formula

\(L_{10} = a_1 \left(\frac{C}{P}\right)^p \ (10^6\ \text{rev}), \quad p = 3\ \text{ball}, \ \tfrac{10}{3}\ \text{roller}\)

\(L_{10h} = \frac{L_{10} \times 10^6}{n}\)

Variables

Symbol Meaning SI unit
\(\text{type}\) Bearing type -
\(C\) Basic dynamic load rating (catalogue) N
\(P\) Equivalent dynamic load N
\(n\) Speed 1/s
\(a_1\) Life factor for reliability (1 for 90 %) -
\(C/P\) Load ratio -
\(L_{10}\) Rating life, millions of revolutions -
\(L_{10h}\) Rating life in operating hours s
\(p\) Life exponent (3 ball, 10/3 roller) -

Method and standards

The Lundberg–Palmgren rating life used in bearing catalogues and in ISO 281's basic life; the reliability factor a₁ is entered by you from the maker's data.

Where it is used

  • Choosing bearings for pumps, fans and motors.
  • Checking whether a heavier load shortens life too much.
  • Planning bearing replacement.

Common mistakes

  • Using the static rating C₀ instead of the dynamic rating C.
  • Forgetting to combine radial and axial loads into P.
  • Ignoring lubrication and contamination, which often govern.

Assumptions and limits

  • Basic life only: no a_ISO factor.
  • Constant load and speed.
  • A load above the dynamic rating C is flagged: the basic rating life does not apply there.

References

  • Lundberg and Palmgren (1947, 1952); basic rating life of ISO 281

Questions and answers

How long does a 6308 bearing last at 4 kN and 1 450 rpm?

C/P = 7.68, so L10 = 452 million revolutions, about 5 200 hours.

Why does a roller bearing use 10/3?

Line contact makes life less sensitive to load than point contact; the exponent is 3 for ball and 10/3 for roller bearings.

What does L10 mean?

The life 90 % of a large group of identical bearings reach or exceed. For higher reliability multiply by the factor from the catalogue.

Method and article reviewed by FireCAD engineering on 12 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.