FireCADCalc

Spur and Helical Gear Tooth Forces from Power and Speed

Tangential, radial and axial forces on spur or helical gear teeth from the power, speed and pitch diameter, with pressure angle and helix angle, for bearing loads.

Inputs

Examples: 15 kW at 1 440 rpm, 80 mm spur pinion45 kW at 960 rpm, 150 mm helical, 15°5 kW at 2 900 rpm, 40 mm helical 30°

Results

Torque on the gear16.464N·m
Tangential force0.82322kN
Radial (separating) force0.34598kN
Axial (thrust) force0.47528kN
Total tooth force1.0116kN
Pitch line velocity6.0737m/s

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: 15 kW at 1 440 rpm, 80 mm spur pinion. The inputs, in the units selected above:

InputValue
Power transmitted15.000 kW
Speed of the gear1,440.0 rpm
Pitch diameter80.000 mm
Normal pressure angle20.000 °
Helix angle (0 for spur gears)0 °

Applying the formula below gives:

ResultValue
Torque on the gear99.472 N·m
Tangential force2.4868 kN
Radial (separating) force0.90512 kN
Axial (thrust) force0 kN
Total tooth force2.6464 kN
Pitch line velocity6.0319 m/s

Open this example in the calculator and change any input.

Formula

\(W_t = \frac{2T}{d}, \quad W_r = W_t\, \frac{\tan\phi_n}{\cos\psi}, \quad W_a = W_t \tan\psi\)

Variables

Symbol Meaning SI unit
\(P\) Power transmitted W
\(n\) Speed of the gear 1/s
\(d\) Pitch diameter m
\(\phi_n\) Normal pressure angle rad
\(\psi\) Helix angle (0 for spur gears) rad
\(T\) Torque on the gear N·m
\(W_t\) Tangential force N
\(W_r\) Radial (separating) force N
\(W_a\) Axial (thrust) force N
\(W\) Total tooth force N
\(v\) Pitch line velocity m/s

Method and standards

Resolution of the normal tooth force.

Where it is used

  • Bearing and shaft design.
  • Gearbox checks.

Common mistakes

  • Using tip diameter.
  • Forgetting axial thrust of helical gears.

Assumptions and limits

  • Friction neglected.

References

  • Shigley's Mechanical Engineering Design (Budynas and Nisbett)
  • ch. 13 (W_t = 2T/d, W_r = W_t tan φ_n / cos ψ, W_a = W_t tan ψ)

Questions and answers

What forces does a 80 mm pinion carry at 15 kW and 1440 rpm?

Torque 99.5 N·m, tangential 2487 N, radial 905 N.

What does a helix add?

An axial thrust W_t tan ψ that the bearings must take.

Which diameter?

The pitch diameter of the gear whose speed is entered.

Method and article reviewed by FireCAD engineering on 12 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.