FireCADCalc

Screw Jack: Effort, Torque and Efficiency

Effort at the handle, torque and efficiency of a screw jack with square threads from the load, pitch, mean diameter, friction and handle length, with self-locking.

Inputs

Examples: 50 kN, 8 mm lead, 46 mm mean, μ 0.12, 0.5 m handle10 kN, 6 mm, 30 mm, μ 0.1, 0.3 mSteep 2-start 20 mm lead, 40 mm, μ 0.05

Results

Self-locking: the load does not lower by itself (friction angle above the helix angle).

Helix angle tan α = p/(π d_m)3.6426°
Torque to raise24.707N·m
Effort at the handle0.082355kN
Efficiency tan α / tan(α + φ)38.651%
Torque to lower (negative = runs down by itself)5.4162N·m

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: 50 kN, 8 mm lead, 46 mm mean, μ 0.12, 0.5 m handle. The inputs, in the units selected above:

InputValue
Load lifted50.000 kN
Lead of the thread (pitch × starts)8.0000 mm
Mean thread diameter46.000 mm
Coefficient of friction of the thread0.12000 -
Handle length (radius of the effort)0.50000 m

Applying the formula below gives:

ResultValue
Helix angle tan α = p/(π d_m)3.1686 °
Torque to raise203.01 N·m
Effort at the handle0.40602 kN
Efficiency tan α / tan(α + φ)31.359 %
Torque to lower (negative = runs down by itself)73.847 N·m

Open this example in the calculator and change any input.

Formula

\(\tan\alpha = \frac{p}{\pi d_m}, \quad T = W\frac{d_m}{2}\tan(\alpha + \phi), \quad \eta = \frac{\tan\alpha}{\tan(\alpha + \phi)}, \quad \tan\phi = \mu\)

Variables

Symbol Meaning SI unit
\(W\) Load lifted N
\(p\) Lead of the thread (pitch × starts) m
\(d_m\) Mean thread diameter m
\(\mu\) Coefficient of friction of the thread -
\(R\) Handle length (radius of the effort) m
\(\alpha\) Helix angle tan α = p/(π d_m) rad
\(T\) Torque to raise N·m
\(P_e\) Effort at the handle N
\(\eta\) Efficiency tan α / tan(α + φ) -
\(T_L\) Torque to lower (negative = runs down by itself) N·m

Method and standards

Unwrapped thread as an inclined plane.

Where it is used

  • Jacks, vices and presses.
  • Machine design examinations.

Common mistakes

  • Pitch instead of lead for multi-start.
  • Forgetting collar friction.

Assumptions and limits

  • Square thread, no collar friction.

References

  • Square-thread screw on an inclined plane (textbook; Shigley's Mechanical Engineering Design (Budynas and Nisbett), ch. 8)

Questions and answers

Effort to lift 50 kN with an 8 mm lead, 46 mm mean diameter, μ 0.12, 0.5 m handle?

Torque 203 N·m, effort 406 N.

Why is efficiency below 50 %?

Every self-locking screw has efficiency under 50 %.

What about collar friction?

Add it separately; see the power screw calculator.

Method and article reviewed by FireCAD engineering on 12 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.