FireCADCalc

Power Screw Torque (Acme or Trapezoidal) with Collar Friction

Torque to raise and lower a load with an Acme or trapezoidal power screw including thread angle and collar friction, with efficiency and self-locking check.

Inputs

Examples: Shigley-type: 6.4 kN, 8 mm lead, 28 mm mean, Acme, f 0.08, 40 mm collarSquare thread, no collar: 10 kN, 5 mm, 22.5 mm, f 0.1Trapezoidal 30°: 25 kN, 6 mm, 37 mm, f 0.12, thrust bearing f 0.01

Results

Self-locking: torque is needed to lower the load.

The lowering torque shown is for the thread only; with collar friction the total torque to lower is T_L + T_c = 39.62 N·m. Self-locking is judged on the thread alone (collar friction adds holding torque).

Torque to raise (thread)81.856N·m
Torque to lower (thread)33.371N·m
Collar torque6.2500N·m
Total torque to raise88.106N·m
Overall efficiency F l /(2π T)27.096%

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: Shigley-type: 6.4 kN, 8 mm lead, 28 mm mean, Acme, f 0.08, 40 mm collar. The inputs, in the units selected above:

InputValue
Axial load6.4000 kN
Lead8.0000 mm
Mean thread diameter28.000 mm
Half thread angle (14.5° Acme, 15° trapezoidal, 0 square)14.500 °
Thread friction0.080000 -
Mean collar diameter40.000 mm
Collar friction0.080000 -

Applying the formula below gives:

ResultValue
Torque to raise (thread)15.670 N·m
Torque to lower (thread)-0.73935 N·m
Collar torque10.240 N·m
Total torque to raise25.910 N·m
Overall efficiency F l /(2π T)31.450 %

Open this example in the calculator and change any input.

Formula

\(T_R = \frac{F d_m}{2}\, \frac{l + \pi f d_m \sec\alpha}{\pi d_m - f l \sec\alpha}, \quad T_L = \frac{F d_m}{2}\, \frac{\pi f d_m \sec\alpha - l}{\pi d_m + f l \sec\alpha}, \quad T_c = \frac{F f_c d_c}{2}\)

Variables

Symbol Meaning SI unit
\(F\) Axial load N
\(l\) Lead m
\(d_m\) Mean thread diameter m
\(\alpha\) Half thread angle (14.5° Acme, 15° trapezoidal, 0 square) rad
\(f\) Thread friction -
\(d_c\) Mean collar diameter m
\(f_c\) Collar friction -
\(T_R\) Torque to raise (thread) N·m
\(T_L\) Torque to lower (thread) N·m
\(T_c\) Collar torque N·m
\(T\) Total torque to raise N·m
\(e\) Overall efficiency F l /(2π T) -

Method and standards

Force analysis of a thread with flank angle.

Where it is used

  • Lifting tables, presses and actuators.
  • Machine design examinations.

Common mistakes

  • Full thread angle instead of half.
  • Leaving out the collar.

Assumptions and limits

  • Uniform friction.
  • The lowering torque is for the thread only; the total to lower is T_L + T_c (given in a note). Self-locking is judged on the thread alone, which is conservative.

References

  • Shigley's Mechanical Engineering Design (Budynas and Nisbett)
  • ch. 8 (power screws, raise and lower torque with thread angle; collar torque F f_c d_c / 2)

Questions and answers

Why does thread angle matter?

The normal force rises by sec α, so friction torque rises too.

What share is collar friction?

Often a third or more of the total; a thrust bearing removes most of it.

Is the screw self-locking?

If the lowering torque is positive.

Method and article reviewed by FireCAD engineering on 12 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.