FireCADCalc

Plate Clutch Torque (Uniform Wear and Uniform Pressure)

Torque capacity of a single or multi-plate friction clutch from the axial force, friction and friction radii, by the uniform wear and uniform pressure theories.

Inputs

Examples: 4 kN, μ 0.3, 250/150 mm, single plate (2 faces)Multi-plate: 2 kN, μ 0.1 oil, 90/60 mm, 8 facesDisc brake-like: 10 kN, μ 0.35, 200/100 mm, 2 faces

Results

Design on uniform wear: it gives the lower (safe) torque once the lining has bedded in.

Torque, uniform wear (worn clutch)240.00N·m
Torque, uniform pressure (new clutch)245.00N·m
Highest pressure (uniform wear, at the inner radius)169.77kPa
Power at the speed (uniform wear)37.699kW

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: 4 kN, μ 0.3, 250/150 mm, single plate (2 faces). The inputs, in the units selected above:

InputValue
Axial clamping force4.0000 kN
Coefficient of friction0.30000 -
Outer radius of the friction face125.00 mm
Inner radius75.000 mm
Number of friction surfaces2.0000 -
Speed (for the power)1,500.0 rpm

Applying the formula below gives:

ResultValue
Torque, uniform wear (worn clutch)240.00 N·m
Torque, uniform pressure (new clutch)245.00 N·m
Highest pressure (uniform wear, at the inner radius)169.77 kPa
Power at the speed (uniform wear)37.699 kW

Open this example in the calculator and change any input.

Formula

\(T_w = n\, \mu F\, \frac{r_o + r_i}{2}, \quad T_p = n\, \mu F\, \frac{2}{3}\, \frac{r_o^3 - r_i^3}{r_o^2 - r_i^2}, \quad p_{max} = \frac{F}{2\pi r_i (r_o - r_i)}\)

Variables

Symbol Meaning SI unit
\(F\) Axial clamping force N
\(\mu\) Coefficient of friction -
\(r_o\) Outer radius of the friction face m
\(r_i\) Inner radius m
\(n\) Number of friction surfaces -
\(N\) Speed (for the power) 1/s
\(T_w\) Torque, uniform wear (worn clutch) N·m
\(T_p\) Torque, uniform pressure (new clutch) N·m
\(p_{max}\) Highest pressure (uniform wear, at the inner radius) Pa
\(P\) Power at the speed (uniform wear) W

Method and standards

Integration of friction over the annulus.

Where it is used

  • Clutch selection and checks.
  • Machine design examinations.

Common mistakes

  • Counting one face for a single plate.
  • Designing on uniform pressure.

Assumptions and limits

  • Flat annular faces. With an inner radius of 0 the uniform-wear peak pressure is unbounded and is not shown.

References

  • Shigley's Mechanical Engineering Design (Budynas and Nisbett)
  • ch. 16 (disc clutches, uniform wear and uniform pressure)

Questions and answers

4 kN on a 250/150 mm single-plate clutch (two faces), μ 0.3?

Uniform wear 240 N·m; uniform pressure 245 N·m.

Why two theories?

New linings have uniform pressure; once worn, uniform wear, which gives less torque.

How many surfaces does a single plate have?

Two: one each side.

Method and article reviewed by FireCAD engineering on 12 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.