FireCADCalc

Spur Gear Tooth Bending Stress (Lewis)

Tooth bending stress of a spur gear by the Lewis equation with the velocity factor, from transmitted power, speed, module, face width and the Lewis form factor.

Thermal power plantProcess steam and utilitiesSugar mill and cogenerationChemical and fertiliserPulp and paperFood, dairy and textile

Inputs

Examples: 20 T, m 4, 40 mm, 15 kW at 1,450 rpm, cut30 T, m 6, 70 mm, 75 kW at 960 rpm, hobbed

Results

Lewis equation with Barth-type velocity factors (Shigley). A first sizing check: final design uses AGMA or ISO 6336 factors for load distribution, geometry and life. Y for 20° full-depth teeth: 0.322 at 20 teeth, 0.359 at 30, 0.409 at 50.

Pitch diameter80.000mm
Pitch-line velocity6.0737m/s
Tangential load2.4696kN
Velocity factor0.50108
Bending stress95.665MPa

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: 20 T, m 4, 40 mm, 15 kW at 1,450 rpm, cut. The inputs, in the units selected above:

InputValue
Power transmitted15.000 kW
Pinion speed1,450.0 rpm
Pinion teeth20.000 -
Module4.0000 mm
Face width40.000 mm
Lewis form factor (from z and pressure angle)0.32200 -
Velocity factor formCut or milled teeth: 6.1/(6.1 + v)

Applying the formula below gives:

ResultValue
Pitch diameter80.000 mm
Pitch-line velocity6.0737 m/s
Tangential load2.4696 kN
Velocity factor0.50108
Bending stress95.665 MPa

Open this example in the calculator and change any input.

Formula

\(\sigma = \frac{F_t}{K_vbmY}, \quad F_t = \frac{P}{v}, \quad v = \pi dN, \quad K_v = \frac{6.1}{6.1 + v}\ (\text{cut}), \quad \frac{3.56}{3.56 + \sqrt{v}}\ (\text{hobbed or shaped}), \quad \frac{5.56}{5.56 + \sqrt{v}}\ (\text{ground})\)

Variables

Symbol Meaning SI unit
\(P\) Power transmitted W
\(N\) Pinion speed 1/s
\(z\) Pinion teeth -
\(m\) Module m
\(b\) Face width m
\(Y\) Lewis form factor (from z and pressure angle) -
\(\text{velocity}\) Velocity factor form -
\(d\) Pitch diameter m
\(v\) Pitch-line velocity m/s
\(F_t\) Tangential load N
\(K_v\) Velocity factor -
\(\sigma\) Bending stress Pa

Method and standards

Lewis equation.

Where it is used

  • Preliminary gear sizing.
  • Checking a replacement gear.

Common mistakes

  • Using the Lewis result as a final rating.
  • Y for the wrong pressure angle.

Assumptions and limits

  • One tooth carries the load at the tip.

References

  • Budynas and Nisbett
  • Shigley's Mechanical Engineering Design
  • 10th ed. (McGraw-Hill, 2015)
  • ch. 14 (Lewis bending equation and velocity factors)

Questions and answers

What does the Lewis equation assume?

The tooth is a cantilever loaded at its tip with the whole tangential load; the form factor Y captures the tooth shape.

Why a velocity factor?

Dynamic loads from tooth errors grow with speed; better-finished gears tolerate more.

What do the defaults represent?

A 20-tooth, 4 mm module pinion 40 mm wide carrying 15 kW at 1,450 rpm.

Method and article reviewed by FireCAD engineering on 13 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.