FireCADCalc

Interference (Press) Fit Pressure and Holding Torque

Contact pressure of an interference fit between a hub and a hollow or solid shaft by the Lamé equations, with the hoop stresses, press force and torque capacity.

Inputs

Examples: 50 mm solid shaft, 100 mm hub, 40 µmHollow 80/40 mm shaft in 160 mm hub, 60 µmAluminium (70 GPa) hub 60 mm on 30 mm, 25 µm

Results

Same material for hub and shaft; the shaft hoop stress is compressive.

Contact pressure46.575MPa
Hoop stress at the hub bore77.625MPa
Hoop stress at the shaft surface-77.625MPa
Torque the fit can carry π f p d² l / 27,023.3N·m
Axial press-in force π f p d l175.58kN

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: 50 mm solid shaft, 100 mm hub, 40 µm. The inputs, in the units selected above:

InputValue
Diametral interference40.000 µm
Nominal fit diameter50.000 mm
Hub outside diameter100.00 mm
Shaft bore (0 for solid)0 mm
Modulus (hub and shaft)207.00 GPa
Poisson's ratio0.30000 -
Length of the fit60.000 mm
Coefficient of friction0.12000 -

Applying the formula below gives:

ResultValue
Contact pressure62.100 MPa
Hoop stress at the hub bore103.50 MPa
Hoop stress at the shaft surface-62.100 MPa
Torque the fit can carry π f p d² l / 21,755.8 N·m
Axial press-in force π f p d l70.233 kN

Open this example in the calculator and change any input.

Formula

\(p = \frac{\delta}{d\left[\dfrac{1}{E}\left(\dfrac{d_o^2 + d^2}{d_o^2 - d^2} + \nu\right) + \dfrac{1}{E}\left(\dfrac{d^2 + d_i^2}{d^2 - d_i^2} - \nu\right)\right]}\)

\(T = \frac{\pi f p d^2 l}{2}\)

Variables

Symbol Meaning SI unit
\(\delta\) Diametral interference m
\(d\) Nominal fit diameter m
\(d_o\) Hub outside diameter m
\(d_i\) Shaft bore (0 for solid) m
\(E\) Modulus (hub and shaft) Pa
\(\nu\) Poisson's ratio -
\(l\) Length of the fit m
\(f\) Coefficient of friction -
\(p\) Contact pressure Pa
\(\sigma_{t,o}\) Hoop stress at the hub bore Pa
\(\sigma_{t,i}\) Hoop stress at the shaft surface Pa
\(T\) Torque the fit can carry π f p d² l / 2 N·m
\(F_a\) Axial press-in force π f p d l N

Method and standards

Lamé thick-cylinder solution at the common surface.

Where it is used

  • Gears, couplings and bearings on shafts.
  • Machine design examinations.

Common mistakes

  • Radial instead of diametral interference.
  • Mixed materials with one modulus.

Assumptions and limits

  • Same material, elastic, long hub.
  • No yield check of the hub bore (combined hoop and radial stress), no allowance for surface smoothing (loss of interference on pressing), and hub and shaft of different materials are not supported.

References

  • Shigley's Mechanical Engineering Design (Budynas and Nisbett)
  • ch. 2–3 (press and shrink fits, Lamé thick cylinders)

Questions and answers

A 50 mm solid steel shaft in a 100 mm hub with 40 µm interference?

Pressure about 62 MPa.

What torque can it carry?

π f p d² l / 2 with the friction coefficient of the surfaces.

Which interference?

The actual interference after machining tolerances and surface smoothing.

Method and article reviewed by FireCAD engineering on 12 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.