FireCADCalc

Thick-Walled Cylinder Stresses (Lamé Equations)

Hoop, radial and longitudinal stresses at the bore and the outside of a thick-walled cylinder under internal and external pressure by the Lamé equations.

Inputs

Examples: 30 MPa inside, 100 x 160 mm bore and outsideHydraulic cylinder 200 MPa, 50 x 120 mm10 MPa inside, 4 MPa outside, 200 x 240 mm

Results

Elastic stresses away from ends and openings; tensile positive. Design thickness for a pressure vessel comes from the code you work to.

Hoop stress at the bore68.462MPa
Hoop stress at the outside38.462MPa
Radial stress at the bore-30.000MPa
Radial stress at the outside0MPa
Longitudinal stress (closed ends)19.231MPa
Stress intensity at the bore (Tresca)98.462MPa

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: 30 MPa inside, 100 x 160 mm bore and outside. The inputs, in the units selected above:

InputValue
Internal pressure (gauge)30.000 MPa
External pressure (gauge)0 MPa
Inside radius50.000 mm
Outside radius80.000 mm

Applying the formula below gives:

ResultValue
Hoop stress at the bore68.462 MPa
Hoop stress at the outside38.462 MPa
Radial stress at the bore-30.000 MPa
Radial stress at the outside0 MPa
Longitudinal stress (closed ends)19.231 MPa
Stress intensity at the bore (Tresca)98.462 MPa

Open this example in the calculator and change any input.

Formula

\(A = \frac{p_i r_i^2 - p_o r_o^2}{r_o^2 - r_i^2}, \quad B = \frac{(p_i - p_o) r_i^2 r_o^2}{r_o^2 - r_i^2}\)

\(\sigma_\theta = A + \frac{B}{r^2}, \quad \sigma_r = A - \frac{B}{r^2}, \quad \sigma_l = A\)

Variables

Symbol Meaning SI unit
\(p_i\) Internal pressure (gauge) Pa
\(p_o\) External pressure (gauge) Pa
\(r_i\) Inside radius m
\(r_o\) Outside radius m
\(\sigma_{\theta,i}\) Hoop stress at the bore Pa
\(\sigma_{\theta,o}\) Hoop stress at the outside Pa
\(\sigma_{r,i}\) Radial stress at the bore Pa
\(\sigma_{r,o}\) Radial stress at the outside Pa
\(\sigma_l\) Longitudinal stress (closed ends) Pa
\(\sigma_{\theta,i} - \sigma_{r,i}\) Stress intensity at the bore (Tresca) Pa
\(A, B\) Lamé constants Pa, N

Method and standards

Lamé's elastic solution for a long cylinder under internal and external pressure; the longitudinal stress is for closed ends.

Where it is used

  • Hydraulic cylinders, high-pressure tubing and accumulators.
  • Shrink fits and press fits (with the interface pressure).
  • Checking thin-wall estimates.

Common mistakes

  • Using diameters where radii are wanted.
  • Treating the result as a code thickness.
  • Forgetting stress concentration at ports.

Assumptions and limits

  • The longitudinal stress A is for closed ends carrying the end thrust; with open ends (a tube whose thrust is taken elsewhere, a press-fitted sleeve) it is zero. Hoop and radial stresses are the same either way.

  • No yield check: compare the stress intensity at the bore (Tresca) with the allowable stress of the code or the material's yield strength.

  • Elastic, homogeneous, far from ends.

  • Tensile positive.

References

  • G. Lamé (1852); Timoshenko
  • Strength of Materials Part II

Questions and answers

What is the bore stress of a 100 mm bore, 160 mm outside cylinder at 30 MPa?

Hoop 68.5 MPa at the bore and 38.5 MPa outside; radial −30 MPa at the bore. The thin-wall formula would give 50 MPa.

Where is the stress highest?

At the bore, where hoop and radial stresses differ most; the Tresca stress intensity there is 98.5 MPa.

When is a cylinder thick?

When the wall is more than about a tenth of the radius; then thin-wall formulas under-estimate the bore stress.

Method and article reviewed by FireCAD engineering on 12 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.