FireCADCalc

Hoop and Longitudinal Stress in a Thin Cylinder (Barlow)

Hoop and longitudinal stress in a thin-walled pipe or cylinder under internal pressure, by Barlow's formula and the mean-diameter formula, with the pressure for a stress.

Tank and drumBoiler attendant and boiler operator examinations

Inputs

Examples: DN150 sch 40 (168.3 x 7.11 mm) at 10 barDN100 (114.3 x 6.02 mm), 40 bar, check at 138 MPaAir receiver shell 1 000 x 8 mm at 10 bar, check 120 MPa

Results

Not a code wall-thickness calculation: design codes add joint efficiency, corrosion allowance, mill tolerance and other factors.

Hoop stress, Barlow (on outside diameter)11.835MPa
Hoop stress on mean diameter11.335MPa
Longitudinal stress (closed ends)5.6677MPa

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: DN150 sch 40 (168.3 x 7.11 mm) at 10 bar. The inputs, in the units selected above:

InputValue
Internal pressure (above the outside pressure)10.000 bar
Outside diameter168.30 mm
Wall thickness7.1100 mm
Stress to check against (0 = none)0 MPa

Applying the formula below gives:

ResultValue
Hoop stress, Barlow (on outside diameter)11.835 MPa
Hoop stress on mean diameter11.335 MPa
Longitudinal stress (closed ends)5.6677 MPa

Open this example in the calculator and change any input.

Formula

\(\sigma_h = \frac{p D_o}{2 t}\)

\(\sigma_{h,m} = \frac{p (D_o - t)}{2 t}, \quad \sigma_l = \frac{p (D_o - t)}{4 t}\)

\(p_S = \frac{2 S t}{D_o}\)

Variables

Symbol Meaning SI unit
\(p\) internal pressure above the outside Pa
\(D_o\) outside diameter m
\(t\) wall thickness m
\(S\) stress to check against Pa
\(\sigma_h\) hoop stress, Barlow Pa
\(\sigma_{h,m}\) hoop stress on mean diameter Pa
\(\sigma_l\) longitudinal stress Pa
\(p_S\) pressure giving the stress S Pa

Method and standards

Equilibrium of half a thin ring gives the hoop stress; Barlow's form uses the outside diameter and is slightly conservative. The longitudinal stress in a closed-ended cylinder is half the hoop stress.

Where it is used

  • Quick checks of pipe and vessel stresses.
  • Estimating test pressures for a known material stress.
  • Teaching and checking calculations.

Common mistakes

  • Using it as a code design thickness.
  • Using absolute pressure instead of the pressure difference.
  • Applying thin-wall formulas to thick walls.

Assumptions and limits

  • Thin wall (D/t above about 20), uniform internal pressure.
  • No corrosion allowance, tolerance or weld efficiency.

References

  • Barlow's formula
  • Thin-wall cylinder theory

Questions and answers

What hoop stress does a DN150 sch 40 pipe see at 10 bar?

About 11.8 MPa by Barlow (168.3 mm OD, 7.11 mm wall); the longitudinal stress is half that.

Is this a code wall thickness?

No. Design codes add joint efficiency, corrosion allowance, mill tolerance and temperature factors; use them for design.

When is the thin-wall formula not good enough?

When D/t is below about 20: use Lamé's thick-cylinder equations, which give a higher stress at the bore.

Method and article reviewed by FireCAD engineering on 12 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.