FireCADCalc

Simply Supported Beam: Moment, Deflection, Stress

Reactions, maximum bending moment, mid-span deflection and bending stress of a simply supported beam under a uniform load and a central point load.

Inputs

Examples: 6 m span, 10 kN/m + 20 kN, steel beam I 8 603 cm⁴, Z 573.6 cm³4 m, 5 kN/m, no point load, I 2 500 cm⁴, Z 250 cm³Pipe rack 8 m, 3 kN/m + 15 kN, I 18 000 cm⁴, Z 900 cm³

Results

Elastic small-deflection theory; check shear, lateral-torsional buckling and local bearing separately to your design code.

Maximum bending moment (mid-span)75.000kN·m
Mid-span deflection15.038mm
Maximum bending stress130.75MPa
Each support reaction40.000kN
Span over deflection398.98

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: 6 m span, 10 kN/m + 20 kN, steel beam I 8 603 cm⁴, Z 573.6 cm³. The inputs, in the units selected above:

InputValue
Span6.0000 m
Uniformly distributed load (including self weight)10.000 kN/m
Point load at mid-span20.000 kN
Modulus of elasticity200.00 GPa
Second moment of area8,603.0 cm⁴
Elastic section modulus573.60 cm³

Applying the formula below gives:

ResultValue
Maximum bending moment (mid-span)75.000 kN·m
Mid-span deflection15.038 mm
Maximum bending stress130.75 MPa
Each support reaction40.000 kN
Span over deflection398.98

Open this example in the calculator and change any input.

Formula

\(R = \frac{wL + P}{2} \qquad M_{max} = \frac{wL^2}{8} + \frac{PL}{4} \qquad \delta_{max} = \frac{5wL^4}{384EI} + \frac{PL^3}{48EI} \qquad \sigma_b = \frac{M_{max}}{Z}\)

Variables

Symbol Meaning SI unit
\(L\) span m
\(w\) distributed load N/m
\(P\) central point load N
\(E\) modulus of elasticity Pa
\(I\) second moment of area m⁴
\(Z\) section modulus m³
\(M_{max}\) maximum moment N·m
\(\delta_{max}\) mid-span deflection m
\(\sigma_b\) bending stress Pa
\(R\) each reaction N
\(L/\delta\) span over deflection –

Method and standards

Euler–Bernoulli small-deflection theory, superposing the uniform and central point load cases.

Where it is used

  • Pipe rack and platform beams.
  • Monorail and lifting beams (with dynamic factors).
  • Equipment supports.

Common mistakes

  • Leaving out self weight.
  • Mixing cm⁴ and mm⁴.
  • Ignoring lateral-torsional buckling.

Assumptions and limits

  • Linear elastic, small deflection; shear and buckling checked separately.
  • The bending stress is not compared with an allowable stress: check it against your design code.

References

  • Euler–Bernoulli beam theory

Questions and answers

What does a 6 m beam with 10 kN/m and a 20 kN centre load do?

75 kN·m at mid-span, 15.0 mm deflection (span/399) and 131 MPa bending stress with I 8603 cm⁴, Z 573.6 cm³.

Where do I get I and Z?

From the section tables of your steel standard, or calculate them for the shape.

What deflection is acceptable?

Your design code sets it; span/250 to span/360 are common for floors and pipe racks.

Method and article reviewed by FireCAD engineering on 12 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.