FireCADCalc

Fatigue Safety Factor: Goodman, Soderberg and Gerber

Fatigue factor of safety for a fluctuating stress from alternating and mean stress, endurance limit, ultimate and yield strength: Goodman, Soderberg, Gerber.

Inputs

Examples: σa 80, σm 120; Se 200, Sut 600, Sy 400Spring: σa 150, σm 400; Se 300, Sut 1 600, Sy 1 200Fully reversed σa 100; Se 180

Results

Load line through the origin (proportional loading). Goodman is the usual design line; Gerber fits test data best; Soderberg is conservative.

Design factor: the smaller of the chosen fatigue factor and n_y (Shigley pairs Goodman or Gerber with the Langer yield line).

Factor of safety, Goodman1.6667
Factor of safety, Soderberg1.4286
Factor of safety, Gerber2.0711
Factor of safety against first-cycle yield S_y/(σ_a + σ_m)2.0000

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: σa 80, σm 120; Se 200, Sut 600, Sy 400. The inputs, in the units selected above:

InputValue
Alternating stress80.000 MPa
Mean stress (negative = compressive)120.00 MPa
Endurance limit (corrected for size, surface, etc.)200.00 MPa
Ultimate tensile strength600.00 MPa
Yield strength400.00 MPa

Applying the formula below gives:

ResultValue
Factor of safety, Goodman1.6667
Factor of safety, Soderberg1.4286
Factor of safety, Gerber2.0711
Factor of safety against first-cycle yield S_y/(σ_a + σ_m)2.0000

Open this example in the calculator and change any input.

Formula

\(\frac{1}{n_G} = \frac{\sigma_a}{S_e} + \frac{\sigma_m}{S_{ut}}, \quad \frac{1}{n_S} = \frac{\sigma_a}{S_e} + \frac{\sigma_m}{S_y}\)

\(\frac{n\sigma_a}{S_e} + \left(\frac{n\sigma_m}{S_{ut}}\right)^2 = 1\ (\text{Gerber})\)

Variables

Symbol Meaning SI unit
\(\sigma_a\) Alternating stress Pa
\(\sigma_m\) Mean stress (negative = compressive) Pa
\(S_e\) Endurance limit (corrected for size, surface, etc.) Pa
\(S_{ut}\) Ultimate tensile strength Pa
\(S_y\) Yield strength Pa
\(n_G\) Factor of safety, Goodman -
\(n_S\) Factor of safety, Soderberg -
\(n_{Ger}\) Factor of safety, Gerber -
\(n_y\) Factor of safety against first-cycle yield S_y/(σ_a + σ_m) -

Method and standards

Mean-stress fatigue criteria along a proportional load line.

Where it is used

  • Shafts, springs and bolts under cyclic loads.
  • Machine design examinations.

Common mistakes

  • Using the uncorrected endurance limit.
  • Ignoring stress concentration.

Assumptions and limits

  • Proportional loading, infinite life.
  • S_y and S_e may not exceed S_ut.
  • For a compressive mean stress all three fatigue factors are S_e/σ_a and the yield factor uses |σ_m|.
  • The design factor is the smaller of the fatigue factor and n_y.

References

  • Shigley's Mechanical Engineering Design (Budynas and Nisbett)
  • ch. 6 (fluctuating stresses: modified Goodman, Soderberg, Gerber)

Questions and answers

σa 80, σm 120 MPa; Se 200, Sut 600, Sy 400 MPa?

Goodman 1.67, Soderberg 1.43.

Which line should I use?

Goodman for design; Soderberg when yielding must be avoided with margin.

Where does S_e come from?

The test endurance limit times the Marin factors for surface, size, load, temperature and reliability.

Method and article reviewed by FireCAD engineering on 12 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.