FireCADCalc

Flywheel Energy, Inertia and Speed Fluctuation

Moment of inertia of a disc or rim flywheel, its stored kinetic energy, the energy given up between two speeds, the coefficient of fluctuation and rim speed.

Inputs

Examples: Disc 500 kg, 0.6 m radius, 1 500 to 1 450 rpmRim 2 t, 1.2 m radius, 300 to 285 rpmGiven 90 kg·m², 0.5 m radius, 1 000 to 950 rpm

Results

Check the rim speed against the material's safe limit (from the maker or a design text); the hub and arms add a little inertia to a rim flywheel.

Moment of inertia90.000kg·m²
Kinetic energy at the highest speed493.48kJ
Energy given up from highest to lowest speed48.114kJ
Coefficient of speed fluctuation5.1282%
Rim speed at the highest speed52.360m/s

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: Disc 500 kg, 0.6 m radius, 1 500 to 1 450 rpm. The inputs, in the units selected above:

InputValue
FlywheelSolid disc (I = m r²/2)
Mass500.00 kg
Outer radius0.60000 m
Moment of inertia (when entered)90.000 kg·m²
Highest speed1,500.0 rpm
Lowest speed1,450.0 rpm

Applying the formula below gives:

ResultValue
Moment of inertia90.000 kg·m²
Kinetic energy at the highest speed1,110.3 kJ
Energy given up from highest to lowest speed72.788 kJ
Coefficient of speed fluctuation3.3898 %
Rim speed at the highest speed94.248 m/s

Open this example in the calculator and change any input.

Formula

\(I = \tfrac12 m r^2\ (\text{disc}), \quad I = m r^2\ (\text{rim})\)

\(E_1 = \tfrac12 I \omega_1^2, \quad \Delta E = \tfrac12 I (\omega_1^2 - \omega_2^2)\)

\(C_s = \frac{n_1 - n_2}{(n_1 + n_2)/2}, \quad v = \omega_1 r\)

Variables

Symbol Meaning SI unit
\(\text{shape}\) Flywheel -
\(m\) Mass kg
\(r\) Outer radius m
\(I\) Moment of inertia (when entered) kg·m²
\(n_1\) Highest speed 1/s
\(n_2\) Lowest speed 1/s
\(E_1\) Kinetic energy at the highest speed J
\(\Delta E\) Energy given up from highest to lowest speed J
\(C_s\) Coefficient of speed fluctuation -
\(v\) Rim speed at the highest speed m/s
\(\omega_1, \omega_2\) Angular speeds 2πn rad/s

Method and standards

Kinetic energy of a rotating body; the energy exchanged between two speeds is the difference of the two energies.

Where it is used

  • Press, crusher and reciprocating compressor drives.
  • Run-down time and stored energy of large fans.
  • Start-up energy of high-inertia loads.

Common mistakes

  • Using rpm directly instead of rad/s.
  • Using the outer radius for a thick rim.
  • Ignoring the hub and arms.

Assumptions and limits

  • Rigid body; uniform disc or thin rim.
  • The rim speed is not compared with a material limit; zero mass or radius is flagged.

References

  • Rigid-body rotation
  • E = I ω²/2 (classical mechanics)

Questions and answers

How much energy does a 500 kg, 0.6 m radius disc store at 1 500 rpm?

Its inertia is 90 kg·m², so 1.11 MJ; slowing to 1 450 rpm releases 72.8 kJ.

Why is a rim better than a disc?

The mass is all at the radius, so the same mass gives twice the inertia: I = m r² against m r²/2.

What limits a flywheel?

Rim speed: the hoop stress grows with its square. Check it against the material's safe speed.

Method and article reviewed by FireCAD engineering on 12 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.