FireCADCalc

Cone Clutch Torque and Axial Force

Friction torque of a cone clutch from axial force, friction, cone angle and mean radius (uniform wear), and the axial force needed for a torque.

Thermal power plantProcess steam and utilitiesSugar mill and cogenerationChemical and fertiliserPulp and paperFood, dairy and textile

Inputs

Examples: 300/240 mm, 12.5°, 2 kNLarge 20°, 5 kN

Results

Uniform-wear theory (worn clutches); p_max is not checked against the lining's limit. Engaging under slip needs more axial force, W(sin α + μ cos α)/sin α times the value here.

Mean radius225.00mm
Torque capacity (uniform wear)986.78N·m
Axial force for the required torque4,053.6N
Maximum pressure (at inner radius)79.577kPa

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: 300/240 mm, 12.5°, 2 kN. The inputs, in the units selected above:

InputValue
Axial (engaging) force2,000.0 N
Friction coefficient0.25000 -
Semi-cone angle12.500 °
Outer radius150.00 mm
Inner radius120.00 mm
Required torque (for the force)200.00 N·m

Applying the formula below gives:

ResultValue
Mean radius135.00 mm
Torque capacity (uniform wear)311.87 N·m
Axial force for the required torque1,282.6 N
Maximum pressure (at inner radius)88.419 kPa

Open this example in the calculator and change any input.

Formula

\(T = \frac{\mu Wr_m}{\sin\alpha}, \quad r_m = \frac{r_o + r_i}{2}, \quad p_{max} = \frac{W}{2\pi r_i(r_o - r_i)}\)

Variables

Symbol Meaning SI unit
\(W\) Axial (engaging) force N
\(\mu\) Friction coefficient -
\(\alpha\) Semi-cone angle rad
\(r_o\) Outer radius m
\(r_i\) Inner radius m
\(T_{req}\) Required torque (for the force) N·m
\(r_m\) Mean radius m
\(T\) Torque capacity (uniform wear) N·m
\(W_{req}\) Axial force for the required torque N
\(p_{max}\) Maximum pressure (at inner radius) Pa

Method and standards

Uniform-wear clutch theory.

Where it is used

  • Machine tool and winch clutches.
  • Teaching.

Common mistakes

  • Using uniform pressure for worn clutches.
  • Very small cone angles.

Assumptions and limits

  • Uniform wear; rigid cone; force for steady (non-slipping) engagement.
  • p_max is not compared with the lining's allowable pressure. Engaging while slipping needs W(sin α + μ cos α)/sin α.
  • A semi-cone angle below about 12.5° is flagged.

References

  • Rattan
  • Theory of Machines
  • 4th ed. (McGraw-Hill, 2014); Bhandari
  • Design of Machine Elements
  • 4th ed. (McGraw-Hill, 2017) (cone clutch, uniform wear)
  • Budynas and Nisbett
  • Shigley's Mechanical Engineering Design
  • 10th ed. (McGraw-Hill, 2015)
  • ch. 16

Questions and answers

Why does a cone multiply torque?

The wedge raises the normal force on the friction surface by 1/sin α for the same axial push.

Why not make α very small?

Below about 12.5° the cone tends to jam and needs force to release.

What do the defaults represent?

A cone clutch 300/240 mm with a 12.5° semi-angle and 2 kN engaging force.

Method and article reviewed by FireCAD engineering on 13 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.