FireCADCalc

Roller Chain Length and Centre Distance

Number of links of a roller chain for two sprockets and a centre distance, rounded to an even number, and the exact centre distance for that chain length.

Inputs

Examples: ANSI 60 (19.05 mm), 19 and 57 teeth, 762 mm12.7 mm pitch, 17 and 34 teeth, 500 mm25.4 mm pitch, 21 and 21 teeth, 1 m

Results

Allow adjustment or a tensioner for chain wear; an odd number of links needs an offset link.

Chain length in pitches (exact)104.43
Links, rounded up to an even number106.00
Centre distance for that chain510.02mm
Chain length1,346.2mm
Speed ratio z₂/z₁2.0000

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: ANSI 60 (19.05 mm), 19 and 57 teeth, 762 mm. The inputs, in the units selected above:

InputValue
Chain pitch19.050 mm
Teeth on the small sprocket19.000 -
Teeth on the large sprocket57.000 -
Centre distance wanted762.00 mm

Applying the formula below gives:

ResultValue
Chain length in pitches (exact)118.91
Links, rounded up to an even number120.00
Centre distance for that chain772.46 mm
Chain length2,286.0 mm
Speed ratio z₂/z₁3.0000

Open this example in the calculator and change any input.

Formula

\(\frac{L}{p} = \frac{2C}{p} + \frac{z_1 + z_2}{2} + \left(\frac{z_2 - z_1}{2\pi}\right)^2 \frac{p}{C}\)

\(C_e = \frac{p}{4}\left[A + \sqrt{A^2 - 8\left(\frac{z_2 - z_1}{2\pi}\right)^2}\right], \quad A = N_L - \frac{z_1 + z_2}{2}\)

Variables

Symbol Meaning SI unit
\(p\) Chain pitch m
\(z_1\) Teeth on the small sprocket -
\(z_2\) Teeth on the large sprocket -
\(C\) Centre distance wanted m
\(L/p\) Chain length in pitches (exact) -
\(N_L\) Links, rounded up to an even number -
\(C_e\) Centre distance for that chain m
\(L\) Chain length m
\(i\) Speed ratio z₂/z₁ -
\(A\) Links less the mean tooth number -

Method and standards

The chain length in pitches for two sprockets (Shigley, ch. 17); the second formula is its exact inverse for the rounded even link count.

Where it is used

  • Designing chain drives for conveyors, feeders and agitators.
  • Ordering replacement chain.
  • Setting the adjustment range.

Common mistakes

  • Using sprocket diameters instead of tooth numbers.
  • Rounding down so the chain is too tight.
  • Forgetting adjustment for wear.

Assumptions and limits

  • Two sprockets, open drive; no idlers.
  • About 30 to 50 pitches is the usual centre distance; under 30 or over 80 pitches is flagged.

References

  • Shigley's Mechanical Engineering Design
  • ch. 17 (roller chain geometry)

Questions and answers

How many links for 19 and 57 teeth at 762 mm with 19.05 mm pitch?

118.9 pitches, so 120 links; the centre distance then becomes 772.5 mm.

Why an even number of links?

Inner and outer links alternate; an odd number needs an offset link, which is weaker.

What centre distance is usual?

About 30 to 50 pitches; long drives need idlers or slack-side support.

Method and article reviewed by FireCAD engineering on 12 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.