FireCADCalc

Bolted Joint Stiffness, Joint Constant and Bolt Load

Bolt and member stiffness of a bolted joint (frustum method), the joint constant, and the bolt load, member load and separation load for a preload and external load.

Inputs

Examples: M12, 40 mm grip, steel, 40 kN preload, 20 kN loadM20, 60 mm grip, steel bolt in cast iron (100 GPa)M10, 25 mm grip, 30 kN load on 25 kN preload (separates)M12, 40 mm grip with 10 mm of thread in it

0 if the grip is all plain shank. The threaded part uses the tensile stress area A_t.

Results

Bolt stiffness (shank and threaded lengths in series)1,083,849N/mm
Member stiffness (30° frustum, washer face 1.5 d)1,870,529N/mm
Joint constant k_b/(k_b + k_m)36.686%
Bolt load F_i + C P (P once separated)138.34kN
Member clamp load F_i − (1 − C) P (0 once separated)88.343kN
External load to separate the joint189.53kN

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: M12, 40 mm grip, steel, 40 kN preload, 20 kN load. The inputs, in the units selected above:

InputValue
Bolt nominal diameter12.000 mm
Tensile stress area of the thread84.300 mm²
Grip length (members clamped)40.000 mm
Modulus of the bolt207.00 GPa
Modulus of the members (same material)207.00 GPa
Preload40.000 kN
External tensile load on the joint20.000 kN
Threaded length within the grip0 mm

Applying the formula below gives:

ResultValue
Bolt stiffness (shank and threaded lengths in series)585,279 N/mm
Member stiffness (30° frustum, washer face 1.5 d)2,235,068 N/mm
Joint constant k_b/(k_b + k_m)20.752 %
Bolt load F_i + C P (P once separated)44.150 kN
Member clamp load F_i − (1 − C) P (0 once separated)24.150 kN
External load to separate the joint50.474 kN

Open this example in the calculator and change any input.

Formula

\(k_b = \frac{A_d A_t E_b}{A_d l_t + A_t (l - l_t)}, \quad A_d = \frac{\pi d^2}{4}, \quad k_m = \frac{0.5774\pi E_m d}{2\ln\dfrac{5(0.5774\,l + 0.5d)}{0.5774\,l + 2.5d}}\)

\(C = \frac{k_b}{k_b + k_m}, \quad F_b = F_i + CP, \quad F_m = F_i - (1 - C)P \quad (P \le P_0), \qquad F_b = P,\ F_m = 0 \quad (P > P_0), \qquad P_0 = \frac{F_i}{1 - C}\)

Variables

Symbol Meaning SI unit
\(d\) Bolt nominal diameter m
\(A_t\) Tensile stress area of the thread m²
\(l\) Grip length (members clamped) m
\(E_b\) Modulus of the bolt Pa
\(E_m\) Modulus of the members (same material) Pa
\(F_i\) Preload N
\(P\) External tensile load on the joint N
\(l_t\) Threaded length within the grip m
\(A_d\) Shank (nominal) area π d²/4 m²
\(k_b\) Bolt stiffness (shank and threaded lengths in series) N/m
\(k_m\) Member stiffness (30° frustum, washer face 1.5 d) N/m
\(C\) Joint constant k_b/(k_b + k_m) -
\(F_b\) Bolt load F_i + C P (P once separated) N
\(F_m\) Member clamp load F_i − (1 − C) P (0 once separated) N
\(P_0\) External load to separate the joint N

Method and standards

Spring model of bolt and clamped members.

Where it is used

  • Flange and cylinder head bolting.
  • Fatigue of bolted joints.

Common mistakes

  • Ignoring threads in the grip.
  • Assuming the bolt takes all the external load.

Assumptions and limits

  • Same-material members; elastic.
  • Bolt stiffness: plain shank (area A_d) over the grip less the threaded length, and the threaded length in the grip at the tensile stress area A_t, in series.
  • Once the external load exceeds P₀ the joint is open: the bolt carries P and the member clamp load is zero.

References

  • Shigley's Mechanical Engineering Design (Budynas and Nisbett)
  • ch. 8 (k_m = 0.5774 π E d / (2 ln(5(0.5774 l + 0.5 d)/(0.5774 l + 2.5 d))), F_b = F_i + C P)

Questions and answers

Why is C small?

The clamped members are much stiffer than the bolt, so they take most of the external load.

What does preload do?

It keeps the joint closed: the bolt sees only C of the external load until separation.

Is the member formula general?

It is for two members of the same material with washer faces; other cases use the general frustum sum.

Method and article reviewed by FireCAD engineering on 12 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.