Worked example
Example: M12, 40 mm grip, steel, 40 kN preload, 20 kN load. The inputs, in the units selected above:
| Input | Value |
|---|---|
| Bolt nominal diameter | 12.000 mm |
| Tensile stress area of the thread | 84.300 mm² |
| Grip length (members clamped) | 40.000 mm |
| Modulus of the bolt | 207.00 GPa |
| Modulus of the members (same material) | 207.00 GPa |
| Preload | 40.000 kN |
| External tensile load on the joint | 20.000 kN |
| Threaded length within the grip | 0 mm |
Applying the formula below gives:
| Result | Value |
|---|---|
| Bolt stiffness (shank and threaded lengths in series) | 585,279 N/mm |
| Member stiffness (30° frustum, washer face 1.5 d) | 2,235,068 N/mm |
| Joint constant k_b/(k_b + k_m) | 20.752 % |
| Bolt load F_i + C P (P once separated) | 44.150 kN |
| Member clamp load F_i − (1 − C) P (0 once separated) | 24.150 kN |
| External load to separate the joint | 50.474 kN |
Open this example in the calculator and change any input.
Formula
\(k_b = \frac{A_d A_t E_b}{A_d l_t + A_t (l - l_t)}, \quad A_d = \frac{\pi d^2}{4}, \quad k_m = \frac{0.5774\pi E_m d}{2\ln\dfrac{5(0.5774\,l + 0.5d)}{0.5774\,l + 2.5d}}\)
\(C = \frac{k_b}{k_b + k_m}, \quad F_b = F_i + CP, \quad F_m = F_i - (1 - C)P \quad (P \le P_0), \qquad F_b = P,\ F_m = 0 \quad (P > P_0), \qquad P_0 = \frac{F_i}{1 - C}\)
Variables
| Symbol | Meaning | SI unit |
|---|---|---|
| \(d\) | Bolt nominal diameter | m |
| \(A_t\) | Tensile stress area of the thread | m² |
| \(l\) | Grip length (members clamped) | m |
| \(E_b\) | Modulus of the bolt | Pa |
| \(E_m\) | Modulus of the members (same material) | Pa |
| \(F_i\) | Preload | N |
| \(P\) | External tensile load on the joint | N |
| \(l_t\) | Threaded length within the grip | m |
| \(A_d\) | Shank (nominal) area π d²/4 | m² |
| \(k_b\) | Bolt stiffness (shank and threaded lengths in series) | N/m |
| \(k_m\) | Member stiffness (30° frustum, washer face 1.5 d) | N/m |
| \(C\) | Joint constant k_b/(k_b + k_m) | - |
| \(F_b\) | Bolt load F_i + C P (P once separated) | N |
| \(F_m\) | Member clamp load F_i − (1 − C) P (0 once separated) | N |
| \(P_0\) | External load to separate the joint | N |
Method and standards
Spring model of bolt and clamped members.
Where it is used
- Flange and cylinder head bolting.
- Fatigue of bolted joints.
Common mistakes
- Ignoring threads in the grip.
- Assuming the bolt takes all the external load.
Assumptions and limits
- Same-material members; elastic.
- Bolt stiffness: plain shank (area A_d) over the grip less the threaded length, and the threaded length in the grip at the tensile stress area A_t, in series.
- Once the external load exceeds P₀ the joint is open: the bolt carries P and the member clamp load is zero.
References
- Shigley's Mechanical Engineering Design (Budynas and Nisbett)
- ch. 8 (k_m = 0.5774 π E d / (2 ln(5(0.5774 l + 0.5 d)/(0.5774 l + 2.5 d))), F_b = F_i + C P)
Questions and answers
Why is C small?
The clamped members are much stiffer than the bolt, so they take most of the external load.
What does preload do?
It keeps the joint closed: the bolt sees only C of the external load until separation.
Is the member formula general?
It is for two members of the same material with washer faces; other cases use the general frustum sum.
Method and article reviewed by FireCAD engineering on 12 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.