FireCADCalc

Bolt Tightening Torque and Preload

Bolt preload as a share of proof load from the tensile stress area and proof strength, and the wrench torque for it by the nut factor (T = K F d).

Inputs

Examples: M20, As 245 mm², proof 600 MPa, 75 %, K 0.2M16, As 157 mm², proof 830 MPa, 70 %, K 0.15 lubricatedM30, As 561 mm², proof 600 MPa, 75 %, K 0.2

For a metric thread, work it out from the diameter and pitch with the bolt stress area calculator (M20 × 2.5 is 245 mm²).
From the bolt property class or grade standard.
About 0.2 for plain steel threads as received; lower with lubricant or anti-seize. Get it from the fastener or lubricant maker for critical joints.

Results

Torque control scatters preload by about ±25 %; where preload matters, use tension control or a load-indicating method.

Tightening torque1,514.7N·m
Bolt preload252.45kN
Proof load336.60kN
Tensile stress at preload450.00MPa

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: M20, As 245 mm², proof 600 MPa, 75 %, K 0.2. The inputs, in the units selected above:

InputValue
Nominal bolt diameter20.000 mm
Tensile stress area245.00 mm²
Proof strength of the bolt600.00 MPa
Preload as a share of proof load75.000 %
Nut factor0.20000 -

Applying the formula below gives:

ResultValue
Tightening torque441.00 N·m
Bolt preload110.25 kN
Proof load147.00 kN
Tensile stress at preload450.00 MPa

Open this example in the calculator and change any input.

Formula

\(F_p = S_p\,A_s \qquad F_i = x\,F_p \qquad T = K\,F_i\,d \qquad \sigma_i = x\,S_p\)

Variables

Symbol Meaning SI unit
\(d\) nominal diameter m
\(A_s\) tensile stress area m²
\(S_p\) proof strength Pa
\(x\) preload share of proof load –
\(K\) nut factor –
\(T\) tightening torque N·m
\(F_i\) preload N
\(F_p\) proof load N
\(\sigma_i\) stress at preload Pa

Method and standards

Short-form torque–tension relation with an empirical nut factor.

Where it is used

  • Flange and pressure-part bolting.
  • Structural and machine joints.
  • Maintenance torque charts.

Common mistakes

  • Using a nut factor for dry threads on lubricated bolts.
  • Using nominal area instead of stress area.
  • Expecting better than ±25 % preload from torque.

Assumptions and limits

  • Nut factor scatter dominates; for critical joints use tension control.
  • The combined (tension plus thread torsion) stress during tightening is not checked; a preload above 90 % of proof load is flagged.

References

  • Short-form torque equation T = K F d

Questions and answers

What torque for an M20 bolt with 600 MPa proof strength at 75 % preload?

Preload 110 kN; torque 441 N·m with K = 0.2.

Why does lubrication matter so much?

Most torque goes into friction; lowering K from 0.2 to 0.15 gives a third more preload at the same torque.

Where do I get the stress area?

From the thread standard's table for the size and pitch.

Method and article reviewed by FireCAD engineering on 12 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.