FireCADCalc

Belt Tensions and Power (Flat and V-Belt, Capstan Equation)

Tight- and slack-side tensions, centrifugal tension and power of a flat or V-belt from the allowable tension, friction, wrap angle and speed, with the speed for maximum power.

PumpFan and blowerElectric motor

Inputs

Examples: Flat belt: 2 kN, mu 0.3, 165°, 0.5 kg/m, 20 m/sV-belt 40° groove: 800 N, mu 0.25, 170°, 0.2 kg/m, 25 m/sFlat belt at low speed: 5 kN, mu 0.35, 180°, 1.2 kg/m, 8 m/s

Results

Capstan (Euler–Eytelwein) equation with centrifugal tension; belt creep and initial tension are not modelled.

Tension ratio e^(μθ) (μ / sin β for a V-belt)2.3725
Centrifugal tension m v²0.20000kN
Tight-side tension T_max − T_c1.8000kN
Slack-side tension0.75870kN
Power transmitted (T₁ − T₂) v20.826kW
Speed for maximum power √(T_max / 3m)36.515m/s
Maximum power (at that speed)28.165kW

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: Flat belt: 2 kN, mu 0.3, 165°, 0.5 kg/m, 20 m/s. The inputs, in the units selected above:

InputValue
Allowable belt tension2.0000 kN
Coefficient of friction0.30000 -
Angle of wrap on the smaller pulley165.00 °
Belt typeFlat belt
V-groove included angle40.000 °
Belt mass per metre0.50000 kg/m
Belt speed20.000 m/s

Applying the formula below gives:

ResultValue
Tension ratio e^(μθ) (μ / sin β for a V-belt)2.3725
Centrifugal tension m v²0.20000 kN
Tight-side tension T_max − T_c1.8000 kN
Slack-side tension0.75870 kN
Power transmitted (T₁ − T₂) v20.826 kW
Speed for maximum power √(T_max / 3m)36.515 m/s
Maximum power (at that speed)28.165 kW

Open this example in the calculator and change any input.

Formula

\(\frac{T_1 - T_c}{T_2 - T_c} = e^{\mu_e \theta}\ \to\ \frac{T_1}{T_2} = e^{\mu_e \theta}\ (T_1 = T_{max} - T_c)\)

\(T_c = m v^2, \quad P = (T_1 - T_2)\, v, \quad \mu_e = \frac{\mu}{\sin\beta}\)

\(v_{opt} = \sqrt{\frac{T_{max}}{3m}}\)

Variables

Symbol Meaning SI unit
\(T_{max}\) Allowable belt tension N
\(\mu\) Coefficient of friction -
\(\theta\) Angle of wrap on the smaller pulley rad
\(\text{belt}\) Belt type -
\(2\beta\) V-groove included angle rad
\(m\) Belt mass per metre kg/m
\(v\) Belt speed m/s
\(T_1/T_2\) Tension ratio e^(μθ) (μ / sin β for a V-belt) -
\(T_c\) Centrifugal tension m v² N
\(T_1\) Tight-side tension T_max − T_c N
\(T_2\) Slack-side tension N
\(P\) Power transmitted (T₁ − T₂) v W
\(v_{opt}\) Speed for maximum power √(T_max / 3m) m/s
\(P_{max}\) Maximum power (at that speed) W

Method and standards

Capstan friction equation with centrifugal tension subtracted from the allowable tension.

Where it is used

  • Fan and pump belt drives.
  • Checking belt slip.
  • Machine design examinations.

Common mistakes

  • Wrap angle in degrees in the exponent.
  • Using the full groove angle instead of half.
  • Ignoring centrifugal tension.

Assumptions and limits

  • Steady drive; creep neglected.
  • No service factor: P is the friction-limited capacity at the allowable tension. Divide it by the drive's service factor (from the belt maker) for the rated power.

References

  • Euler–Eytelwein (capstan) equation
  • Shigley's Mechanical Engineering Design
  • ch. 17

Questions and answers

What does a flat belt carry: 2 kN allowable, μ 0.3, 165° wrap, 0.5 kg/m, 20 m/s?

Centrifugal tension 200 N leaves T₁ = 1800 N; T₁/T₂ = 2.37, T₂ = 759 N; power 20.8 kW.

What speed gives the most power?

v = √(T_max/3m) = 36.5 m/s, giving 28.2 kW.

Why do V-belts grip better?

The wedge multiplies friction by 1/sin(β): a 40° groove makes μ 0.25 act like 0.73.

Method and article reviewed by FireCAD engineering on 12 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.