FireCADCalc

Rolling Bearing Equivalent Load and Rating Life

Equivalent dynamic load of a rolling bearing from radial and axial loads with X and Y factors, and the L10 rating life in revolutions and hours.

Thermal power plantProcess steam and utilitiesSugar mill and cogenerationChemical and fertiliserPulp and paperFood, dairy and textile

Inputs

Examples: Ball bearing C 33 kN, 6 + 2 kN, 1,450 rpmRoller bearing C 120 kN radial 15 kN

Results

X and Y depend on the bearing type and on F_a/(C₀) and F_a/F_r: take them from the bearing maker's catalogue. If F_a/F_r is below the catalogue's e, X = 1 and Y = 0 (the larger of XF_r + YF_a and F_r is used here).

Equivalent dynamic load16.500kN
Rating life (million revolutions)745.29
Rating life12,939h

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: Ball bearing C 33 kN, 6 + 2 kN, 1,450 rpm. The inputs, in the units selected above:

InputValue
Radial load6.0000 kN
Axial load2.0000 kN
Radial factor (bearing catalogue)0.56000 -
Axial factor (bearing catalogue)1.6000 -
Basic dynamic load rating33.000 kN
Life exponentBall bearings (3)
Speed1,450.0 rpm
Load (service) factor1.2000 -

Applying the formula below gives:

ResultValue
Equivalent dynamic load7.8720 kN
Rating life (million revolutions)73.669
Rating life846.77 h

Open this example in the calculator and change any input.

Formula

\(P = f_s\max(XF_r + YF_a,\ F_r), \quad L_{10} = \left(\frac CP\right)^p\ \text{million rev}, \quad L_{10h} = \frac{10^6L_{10}}{60N}\)

Variables

Symbol Meaning SI unit
\(F_r\) Radial load N
\(F_a\) Axial load N
\(X\) Radial factor (bearing catalogue) -
\(Y\) Axial factor (bearing catalogue) -
\(C\) Basic dynamic load rating N
\(p\) Life exponent -
\(N\) Speed 1/s
\(f_s\) Load (service) factor -
\(P\) Equivalent dynamic load N
\(L_{10}\) Rating life (million revolutions) -
\(L_{10h}\) Rating life s

Method and standards

Basic rating life.

Where it is used

  • Bearing selection and replacement.
  • Life checks after load changes.

Common mistakes

  • Using static rating C₀ for life.
  • Forgetting the axial load.

Assumptions and limits

  • Basic rating life; normal lubrication and cleanliness.
  • There is no input for the catalogue's e: when F_a/F_r ≤ e, enter X = 1 and Y = 0 yourself. The larger of XF_r + YF_a and F_r is used as a guard.
  • The roller exponent is the exact 10/3.

References

  • Budynas and Nisbett
  • Shigley's Mechanical Engineering Design
  • 10th ed. (McGraw-Hill, 2015)
  • ch. 11 (equivalent radial load P = XF_r + YF_a; L₁₀ = (C/P)^a)

Questions and answers

What does L₁₀ mean?

The life that 90 % of a large group of identical bearings will reach or exceed.

Why does a small load change matter so much?

Life goes as the cube of C/P for ball bearings: 26 % more load halves the life.

What do the defaults represent?

A deep-groove ball bearing (C = 33 kN) with 6 kN radial and 2 kN axial load at 1,450 rpm.

Method and article reviewed by FireCAD engineering on 13 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.