FireCADCalc

Worm Gear Efficiency, Lead Angle and Self-Locking

Efficiency of a worm gear drive from lead angle, normal pressure angle and friction coefficient, with the lead angle from worm dimensions and a self-locking check.

Inputs

Examples: Two-start, 12.6 mm pitch, 50 mm worm, f 0.05Single-start, 6.28 mm, 40 mm, f 0.1 (self-locking)Four-start, 15.7 mm, 60 mm, f 0.03

Falls with sliding speed; from the maker or textbook charts.

Results

Bearing and churning losses lower the overall efficiency further. Self-locking is not a safe brake under vibration.

Lead z_w p_x6.2800mm
Lead angle2.8610°
Efficiency, worm driving31.785%
Self-locking (1 = yes, 0 = no)1.0000

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: Two-start, 12.6 mm pitch, 50 mm worm, f 0.05. The inputs, in the units selected above:

InputValue
Number of worm starts2.0000 -
Axial pitch of the worm12.600 mm
Worm pitch diameter50.000 mm
Normal pressure angle20.000 °
Coefficient of friction0.050000 -

Applying the formula below gives:

ResultValue
Lead z_w p_x25.200 mm
Lead angle9.1142 °
Efficiency, worm driving74.453 %
Self-locking (1 = yes, 0 = no)0

Open this example in the calculator and change any input.

Formula

\(\tan\lambda = \frac{z_w p_x}{\pi d_w}, \quad \eta = \frac{\cos\phi_n - f\tan\lambda}{\cos\phi_n + f\cot\lambda}, \quad \text{self-locking if } f \ge \cos\phi_n \tan\lambda\)

Variables

Symbol Meaning SI unit
\(z_w\) Number of worm starts -
\(p_x\) Axial pitch of the worm m
\(d_w\) Worm pitch diameter m
\(\phi_n\) Normal pressure angle rad
\(f\) Coefficient of friction -
\(L\) Lead z_w p_x m
\(\lambda\) Lead angle rad
\(\eta\) Efficiency, worm driving -
\(\text{locks}\) Self-locking (1 = yes, 0 = no) -

Method and standards

Force analysis of the worm thread.

Where it is used

  • Gearbox selection.
  • Hoists and turntables.

Common mistakes

  • Relying on self-locking as a brake.
  • Using static friction for running efficiency.

Assumptions and limits

  • Worm driving; bearing losses excluded.

References

  • Shigley's Mechanical Engineering Design (Budynas and Nisbett)
  • ch. 13 (η = (cos φn − f tan λ)/(cos φn + f cot λ); self-locking f ≥ cos φn tan λ)

Questions and answers

A two-start worm, 12.6 mm pitch, 50 mm diameter, f 0.05?

Lead angle 9.11°, efficiency 74 %.

When does a worm lock?

When friction exceeds cos φ_n tan λ, typically single-start worms with small lead angles.

Why are worms inefficient?

The teeth slide rather than roll.

Method and article reviewed by FireCAD engineering on 12 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.