FireCADCalc

V-Belt Drive: Number of Belts and Centrifugal Tension

Belt speed, design power with a service factor, number of V-belts from the rated power per belt, centrifugal tension and the tight- and slack-side tensions.

Thermal power plantProcess steam and utilitiesSugar mill and cogenerationChemical and fertiliserPulp and paperFood, dairy and textile

Inputs

Examples: 22 kW at 1,450 rpm, 200 mm, 6 kW per belt75 kW fan drive

Results

Rated power per belt comes from the belt maker's tables for the section, small pulley diameter and speed (with arc and length corrections). Tensions are at the design power, just at slip. Arc-of-contact and belt-length corrections to the rated power per belt are left to you.

Belt speed24.410m/s
Number of belts9.0000
Centrifugal tension per belt220.47N
Tight-side tension per belt733.89N
Slack-side tension per belt255.94N

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: 22 kW at 1,450 rpm, 200 mm, 6 kW per belt. The inputs, in the units selected above:

InputValue
Transmitted power22.000 kW
Service factor1.3000 -
Rated power per belt (maker's data at this speed and diameter)6.0000 kW
Driver pulley pitch diameter200.00 mm
Driver speed1,450.0 rpm
Belt mass per metre0.19000 kg/m
Belt–groove friction coefficient0.30000 -
Groove angle40.000 °
Wrap angle on the small pulley160.43 °

Applying the formula below gives:

ResultValue
Belt speed15.184 m/s
Number of belts5.0000
Centrifugal tension per belt43.807 N
Tight-side tension per belt455.86 N
Slack-side tension per belt79.152 N

Open this example in the calculator and change any input.

Formula

\(n = \left\lceil\frac{K_sP}{P_b}\right\rceil, \quad T_c = m_bv^2, \quad \frac{T_1 - T_c}{T_2 - T_c} = e^{\mu\theta/\sin\beta}\)

Variables

Symbol Meaning SI unit
\(P\) Transmitted power W
\(K_s\) Service factor -
\(P_b\) Rated power per belt (maker's data at this speed and diameter) W
\(d\) Driver pulley pitch diameter m
\(N\) Driver speed 1/s
\(m_b\) Belt mass per metre kg/m
\(\mu\) Belt–groove friction coefficient -
\(2\beta\) Groove angle rad
\(\theta\) Wrap angle on the small pulley rad
\(v\) Belt speed m/s
\(n\) Number of belts -
\(T_c\) Centrifugal tension per belt N
\(T_1\) Tight-side tension per belt N
\(T_2\) Slack-side tension per belt N

Method and standards

Belt mechanics.

Where it is used

  • Fan, pump and compressor belt drives.
  • Belt replacement and retensioning.

Common mistakes

  • Using flat-belt friction for V-belts.
  • Ignoring the service factor.

Assumptions and limits

  • The rated power per belt is entered as the maker gives it; arc-of-contact and belt-length correction factors must be applied to it before entry. The page warns above about 30 m/s belt speed.

  • Belt at the point of slip at design load.

References

  • Budynas and Nisbett
  • Shigley's Mechanical Engineering Design
  • 10th ed. (McGraw-Hill, 2015)
  • ch. 17 (V-belts: tension ratio e^(μθ/sin β), centrifugal tension)

Questions and answers

Why does the groove raise grip?

The V wedges the belt; effective friction becomes μ/sin β, about three times the flat-belt value.

Why does centrifugal tension matter?

At high belt speed it uses up belt strength without transmitting power; above about 30 m/s V-belts lose capacity fast.

What do the defaults represent?

A 22 kW, 1,450 rpm drive on a 200 mm pulley with B-section-like belts rated 6 kW each.

Method and article reviewed by FireCAD engineering on 13 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.