FireCADCalc

Shaft Diameter for Torque and Bending

Diameter of a solid or hollow shaft for transmitted power and a bending moment, by the maximum shear stress theory with shock and fatigue factors.

PumpFan and blower

Inputs

Examples: 30 kW at 1 450 rpm, 150 N·m bending, 40 MPa, Km 1.5Fan shaft 75 kW at 980 rpm, 600 N·m, 45 MPa, Km 1.5, Kt 1.0Hollow 200 kW at 300 rpm, no bending, 50 MPa, bore 0.6

From the shaft material and your design practice (keyways lower it).

Results

Static strength only: check deflection, critical speed, keyway stress concentration and fatigue for the final size, then round up to a standard diameter.

Torque transmitted730.81N·m
Equivalent torque1,159.3N·m
Shaft diameter (outside)50.815mm
Bore diameter (hollow shaft)0mm

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: 30 kW at 1 450 rpm, 150 N·m bending, 40 MPa, Km 1.5. The inputs, in the units selected above:

InputValue
Power transmitted30.000 kW
Shaft speed1,450.0 rpm
Bending moment at the section150.00 N·m
Allowable shear stress40.000 MPa
Shock and fatigue factor for bending1.5000 -
Shock and fatigue factor for torsion1.0000 -
Bore ratio of a hollow shaft d_i/d_o (0 = solid)0 %

Applying the formula below gives:

ResultValue
Torque transmitted197.57 N·m
Equivalent torque299.43 N·m
Shaft diameter (outside)33.657 mm
Bore diameter (hollow shaft)0 mm

Open this example in the calculator and change any input.

Formula

\(T = \frac{P}{2 \pi n}\)

\(T_e = \sqrt{(K_m M)^2 + (K_t T)^2}\)

\(d_o = \left[\frac{16 T_e}{\pi \tau_a (1 - k^4)}\right]^{1/3}, \quad d_i = k\, d_o\)

Variables

Symbol Meaning SI unit
\(P\) power W
\(n\) speed rev/s
\(M\) bending moment N·m
\(\tau_a\) allowable shear stress Pa
\(K_m\) bending shock and fatigue factor -
\(K_t\) torsion shock and fatigue factor -
\(k\) bore ratio d_i/d_o -
\(T\) torque N·m
\(T_e\) equivalent torque N·m
\(d_o\) outside diameter m
\(d_i\) bore diameter m

Method and standards

Maximum shear stress theory for a shaft under bending and torsion: the equivalent torque with shock and fatigue factors gives the diameter at the allowable shear stress.

Where it is used

  • Sizing pump, fan and conveyor shafts.
  • Checking an existing shaft for a power increase.
  • Comparing solid and hollow shafts.

Common mistakes

  • Ignoring bending from belt pull or overhung loads.
  • Using yield strength directly as the allowable stress.
  • Forgetting the keyway and critical speed.

Assumptions and limits

  • Static strength; deflection, critical speed and detailed fatigue to be checked separately.
  • The factor of safety is inside the allowable shear stress you enter. K_m and K_t are your inputs: machine design texts tabulate the ASME code values for transmission shafting (for a rotating shaft with gradually applied load, K_m = 1.5 and K_t = 1.0; higher for shock loads).

References

  • Maximum shear stress (Tresca) theory with shock and fatigue factors

Questions and answers

What shaft for 30 kW at 1 450 rpm with 150 N·m bending?

About 34 mm solid at 40 MPa allowable shear with Km 1.5; round up to a standard size and check keyway and deflection.

What is equivalent torque?

√((Km M)² + (Kt T)²): the single torque that gives the same maximum shear stress as the combined bending and twisting.

Why is a hollow shaft lighter?

The centre carries little stress; a bore of 0.6 D adds only about 5 % to the outside diameter for the same strength.

Method and article reviewed by FireCAD engineering on 12 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.