Worked example
Example: 1 kN·m on a 50 mm shaft, 14 x 9 x 60 mm key. The inputs, in the units selected above:
| Input | Value |
|---|---|
| Torque transmitted | 1,000.0 N·m |
| Shaft diameter | 50.000 mm |
| Key width | 14.000 mm |
| Key height | 9.0000 mm |
| Key length | 60.000 mm |
| Allowable shear stress of the key | 60.000 MPa |
| Allowable crushing stress | 100.00 MPa |
Applying the formula below gives:
| Result | Value |
|---|---|
| Tangential force at the shaft surface 2T / d | 40.000 kN |
| Shear stress in the key F / (b l) | 47.619 MPa |
| Crushing stress F / (h l / 2) | 148.15 MPa |
| Length needed for shear | 47.619 mm |
| Length needed for crushing | 88.889 mm |
| Key length needed (larger of the two) | 88.889 mm |
Open this example in the calculator and change any input.
Formula
\(F = \frac{2T}{d}, \quad \tau = \frac{F}{b\,l}, \quad \sigma_c = \frac{F}{(h/2)\,l}\)
\(l = \max\left(\frac{F}{b\,\tau_a},\ \frac{2F}{h\,\sigma_{c,a}}\right)\)
Variables
| Symbol | Meaning | SI unit |
|---|---|---|
| \(T\) | Torque transmitted | N·m |
| \(d\) | Shaft diameter | m |
| \(b\) | Key width | m |
| \(h\) | Key height | m |
| \(l\) | Key length | m |
| \(\tau_a\) | Allowable shear stress of the key | Pa |
| \(\sigma_{c,a}\) | Allowable crushing stress | Pa |
| \(F\) | Tangential force at the shaft surface 2T / d | N |
| \(\tau\) | Shear stress in the key F / (b l) | Pa |
| \(\sigma_c\) | Crushing stress F / (h l / 2) | Pa |
| \(l_s\) | Length needed for shear | m |
| \(l_c\) | Length needed for crushing | m |
| \(l_{req}\) | Key length needed (larger of the two) | m |
Method and standards
Force at the shaft surface sheared across the key width and pressed against half its height.
Where it is used
- Couplings, pulleys, gears and impellers.
- Checking a key after a motor upgrade.
- Machine design examinations.
Common mistakes
- Using radius instead of diameter.
- Using full key height for crushing.
- Ignoring the hub material's lower crushing strength.
Assumptions and limits
- Uniform pressure; no fatigue or stress concentration. A key shorter than the length needed is flagged.
References
- Shigley's Mechanical Engineering Design
- ch. 7 (keys)
- V.B. Bhandari
- Design of Machine Elements
- ch. 9
Questions and answers
Is a 14 × 9 × 60 mm key enough for 1 kN·m on a 50 mm shaft?
The force is 40 kN; shear 47.6 MPa is fine, but crushing 148 MPa exceeds 100 MPa. It needs 89 mm length.
Why half the key height?
A sunk key sits half in the shaft and half in the hub, so the crushing area is h/2 × l.
Which governs?
Usually crushing for square-ish keys; the calculator shows both lengths.
Method and article reviewed by FireCAD engineering on 12 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.