FireCADCalc

Hooke's (Universal) Joint: Output Speed Variation

Output shaft speed of a Hooke's (Cardan) joint at a shaft angle and input position, its maximum and minimum, and the speed fluctuation.

Thermal power plantProcess steam and utilitiesSugar mill and cogenerationChemical and fertiliserPulp and paperFood, dairy and textile

Inputs

Examples: 1,000 rpm, 20°, θ 30°500 rpm, 10°, θ 90°

Results

A double Hooke's joint with equal angles and in-phase yokes cancels the fluctuation; constant-velocity joints avoid it altogether.

Output speed at θ968.00rpm
Maximum output speed1,064.2rpm
Minimum output speed939.69rpm
Total fluctuation12.449%

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: 1,000 rpm, 20°, θ 30°. The inputs, in the units selected above:

InputValue
Input speed1,000.0 rpm
Angle between shafts20.000 °
Input shaft position, from the driving yoke perpendicular to the plane of the shafts30.000 °

Applying the formula below gives:

ResultValue
Output speed at θ968.00 rpm
Maximum output speed1,064.2 rpm
Minimum output speed939.69 rpm
Total fluctuation12.449 %

Open this example in the calculator and change any input.

Formula

\(\frac{\omega_2}{\omega_1} = \frac{\cos\alpha}{1 - \sin^2\theta\sin^2\alpha}, \quad N_{2,max} = \frac{N_1}{\cos\alpha}, \quad N_{2,min} = N_1\cos\alpha\)

Variables

Symbol Meaning SI unit
\(N_1\) Input speed 1/s
\(\alpha\) Angle between shafts rad
\(\theta\) Input shaft position, from the driving yoke perpendicular to the plane of the shafts rad
\(N_2\) Output speed at θ 1/s
\(N_{2,max}\) Maximum output speed 1/s
\(N_{2,min}\) Minimum output speed 1/s
\(\Delta N/N_1\) Total fluctuation -

Method and standards

Hooke's joint kinematics.

Where it is used

  • Drive shafts and cardan shafts.
  • Mill and conveyor drives.

Common mistakes

  • Large angles with a single joint.
  • Out-of-phase yokes on a double joint.

Assumptions and limits

  • Rigid joint.
  • θ is measured from the position where the driving yoke is perpendicular to the plane containing both shafts: the output is slowest there (θ = 0°, 180°) and fastest at θ = 90°, 270°.

References

  • Rattan
  • Theory of Machines
  • 4th ed. (McGraw-Hill, 2014); Bhandari
  • Design of Machine Elements
  • 4th ed. (McGraw-Hill, 2017) (Hooke's joint: ω₂/ω₁ = cos α/(1 − sin²θ sin²α))

Questions and answers

Why does the output speed vary?

A single universal joint at an angle is not a constant-velocity joint: output speed swings twice per revolution.

How big is the swing?

At 20° the output varies between 0.94 and 1.06 times the input, about 12 %.

What do the defaults represent?

A shaft at 1,000 rpm through a joint angled at 20°.

Method and article reviewed by FireCAD engineering on 13 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.