FireCADCalc

Helical Compression Spring Rate, Stress and Deflection

Spring rate, spring index, Wahl factor, corrected shear stress and deflection of a helical compression or extension spring of round wire under a load.

Inputs

Examples: 6 mm wire, 45 mm mean diameter, 8 coils, 500 N2 mm wire, 16 mm, 12 coils, 30 NStainless 10 mm wire, 60 mm, 6 coils, 2 kN

Spring steel about 79 GPa; stainless about 69 GPa; phosphor bronze about 41 GPa.

Results

Spring rate66.551N/mm
Spring index D/d6.0000
Wahl stress factor1.2525
Shear stress with the Wahl factor382.74MPa
Deflection under the load30.052mm

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: 6 mm wire, 45 mm mean diameter, 8 coils, 500 N. The inputs, in the units selected above:

InputValue
Wire diameter6.0000 mm
Mean coil diameter45.000 mm
Number of active coils8.0000 -
Shear modulus of the wire79.300 GPa
Load500.00 N

Applying the formula below gives:

ResultValue
Spring rate17.622 N/mm
Spring index D/d7.5000
Wahl stress factor1.1974
Shear stress with the Wahl factor317.62 MPa
Deflection under the load28.373 mm

Open this example in the calculator and change any input.

Formula

\(k = \frac{G d^4}{8 D^3 n_a}, \quad C = \frac{D}{d}\)

\(K_W = \frac{4C - 1}{4C - 4} + \frac{0.615}{C}, \quad \tau = K_W \frac{8 F D}{\pi d^3}, \quad \delta = \frac{F}{k}\)

Variables

Symbol Meaning SI unit
\(d\) Wire diameter m
\(D\) Mean coil diameter m
\(n_a\) Number of active coils -
\(G\) Shear modulus of the wire Pa
\(F\) Load N
\(k\) Spring rate N/m
\(C\) Spring index D/d -
\(K_W\) Wahl stress factor -
\(\tau\) Shear stress with the Wahl factor Pa
\(\delta\) Deflection under the load m

Method and standards

The rate of a close-coiled helical spring follows from the torsion of the wire; Wahl's factor corrects the nominal torsional stress for curvature and direct shear.

Where it is used

  • Designing and checking valve, relief and machine springs.
  • Selecting a stock spring.
  • Checking a spring after a load change.

Common mistakes

  • Counting all coils as active (closed ends are not).
  • Using outside diameter instead of mean diameter.
  • Comparing the stress with tensile instead of torsional strength.

Assumptions and limits

  • Round wire, close-coiled; static load.
  • Fatigue and buckling not checked; the stress is not compared with an allowable, and the solid height (coil clash, which limits the deflection) is not checked.

References

  • A.M. Wahl
  • Mechanical Springs (1963)
  • Shigley's Mechanical Engineering Design
  • ch. 10

Questions and answers

What is the rate of a 6 mm wire spring, 45 mm mean diameter, 8 active coils?

In steel (G 79.3 GPa), 17.6 N/mm; 500 N compresses it 28 mm.

What stress does that load cause?

With spring index 7.5 the Wahl factor is 1.197 and the corrected shear stress 318 MPa.

Why the Wahl factor?

It adds the direct shear and the extra stress on the inside of the coil from curvature; springs fail there first.

Method and article reviewed by FireCAD engineering on 12 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.