FireCADCalc

Disc Brake Torque, Clamping Force and Energy Absorbed

Torque of a caliper disc brake from clamping force, friction and effective radius, with stopping time, energy absorbed and disc temperature rise.

Thermal power plantProcess steam and utilitiesSugar mill and cogenerationChemical and fertiliserPulp and paperFood, dairy and textile

Inputs

Examples: 8 kN pads at 120 mm, 10 kg·m² from 1,000 rpmConveyor brake 3 kN, 50 kg·m² from 1,480 rpm

Results

Single stop with constant torque and no heat loss during the stop; repeated stops need a heat balance over the duty cycle.

Braking torque480.00N·m
Stopping time16.144s
Energy absorbed600.51kJ
Disc temperature rise (all heat to the disc)52.218K

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: 8 kN pads at 120 mm, 10 kg·m² from 1,000 rpm. The inputs, in the units selected above:

InputValue
Clamping force per pad8.0000 kN
Pad friction coefficient0.35000 -
Effective radius of the pads120.00 mm
Friction faces2.0000 -
Rotating inertia being stopped10.000 kg·m²
Initial speed1,000.0 rpm
Disc mass8.0000 kg
Disc specific heat0.46000 kJ/(kg·K)

Applying the formula below gives:

ResultValue
Braking torque672.00 N·m
Stopping time1.5583 s
Energy absorbed54.831 kJ
Disc temperature rise (all heat to the disc)14.900 K

Open this example in the calculator and change any input.

Formula

\(T = \mu Fr_en_f, \quad t_s = \frac{I\omega}{T}, \quad E = \tfrac12I\omega^2, \quad \Delta T = \frac{E}{m_dc_d}\)

Variables

Symbol Meaning SI unit
\(F\) Clamping force per pad N
\(\mu\) Pad friction coefficient -
\(r_e\) Effective radius of the pads m
\(n_f\) Friction faces -
\(I\) Rotating inertia being stopped kg·m²
\(N\) Initial speed 1/s
\(m_d\) Disc mass kg
\(c_d\) Disc specific heat J/(kg·K)
\(T\) Braking torque N·m
\(t_s\) Stopping time s
\(E\) Energy absorbed J
\(\Delta T\) Disc temperature rise (all heat to the disc) K

Method and standards

Friction torque and energy balance.

Where it is used

  • Conveyor, crane and machine brakes.
  • Emergency stop checks.

Common mistakes

  • Counting one face for a two-sided disc.
  • Ignoring repeated-stop heating.

Assumptions and limits

  • Constant torque; adiabatic stop.
  • The stopping time uses the brake torque on the inertia alone: a load torque that also resists (or drives) the shaft during the stop shortens (or lengthens) it.

References

  • Budynas and Nisbett
  • Shigley's Mechanical Engineering Design
  • 10th ed. (McGraw-Hill, 2015)
  • ch. 16 (disc brakes; energy considerations)

Questions and answers

What is the effective radius?

Roughly the mean radius of the pad; for uniform wear it is (r_o + r_i)/2.

Why check temperature?

Pad friction falls (fade) and discs crack if a stop dumps too much energy into too little steel.

What do the defaults represent?

Two-faced caliper, 8 kN per pad at 120 mm radius, stopping 10 kg·m² from 1,000 rpm.

Method and article reviewed by FireCAD engineering on 13 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.