FireCADCalc

Bolt Tensile Stress Area (ISO Metric Thread)

Tensile stress area of a metric bolt or stud from its nominal diameter and pitch, with the pitch and minor diameters of the ISO thread profile.

Inputs

Examples: M12 coarse, pitch 1.75 mmM20 coarse, pitch 2.5 mmM30 coarse, pitch 3.5 mm

The distance between threads, as in M20 × 2.5. Read it from the bolt's designation or measure it with a thread gauge.

Results

Tensile stress area244.79mm²
Pitch diameter18.376mm
Minor diameter of the bolt thread16.933mm
Stress diameter (d₂ + d₃)/217.655mm
Area at the minor diameter225.19mm²

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: M12 coarse, pitch 1.75 mm. The inputs, in the units selected above:

InputValue
Nominal (major) diameter12.000 mm
Thread pitch1.7500 mm

Applying the formula below gives:

ResultValue
Tensile stress area84.267 mm²
Pitch diameter10.863 mm
Minor diameter of the bolt thread9.8530 mm
Stress diameter (d₂ + d₃)/210.358 mm
Area at the minor diameter76.247 mm²

Open this example in the calculator and change any input.

Formula

\(A_s = \frac{\pi}{4}\left(\frac{d_2 + d_3}{2}\right)^2 = \frac{\pi}{4}\,(d - 0.938\,194\,P)^2\)

\(d_2 = d - \tfrac{3\sqrt{3}}{8}P, \quad d_3 = d - \tfrac{17\sqrt{3}}{24}P\)

\(A_3 = \frac{\pi}{4} d_3^2\)

Variables

Symbol Meaning SI unit
\(d\) nominal (major) diameter m
\(P\) thread pitch m
\(d_2\) pitch diameter m
\(d_3\) minor diameter of the bolt (external) thread m
\(d_s\) stress diameter, mean of d_2 and d_3 m
\(A_s\) tensile stress area m²
\(A_3\) area at the minor diameter m²

Method and standards

The ISO metric thread is built on a triangle of height H = (√3/2) P (ISO 68-1). The pitch diameter is d − 2·(3/8)H and the minor diameter of the bolt thread is d − 2·(17/24)H (ISO 724). ISO 898-1 defines the tensile stress area as the circle on the mean of these two diameters. The proof load of a bolt is its proof stress times this area; continue to the bolt torque calculator for preload and torque.

Where it is used

  • Finding the proof load and preload of a bolt for a torque calculation.
  • Checking bolt stress under a known load on a flange, bracket or foundation bolt.
  • Comparing coarse and fine pitches for the same diameter.

Common mistakes

  • Using the shank area: it overstates the strength of the thread by 20–30 %.
  • Using the minor-diameter area as the stress area: it is about 8 % low.
  • Using this for inch (UNC/UNF) threads: their stress area is defined differently.

Assumptions and limits

  • ISO metric (60°) threads only, coarse or fine pitch.
  • Basic dimensions; manufacturing tolerances on the thread are not included.
  • Gives the area only; the bolt's proof and tensile strengths come from its property class.

References

  • ISO 898-1 stress area definition
  • ISO 68-1 / ISO 724 thread profile

Questions and answers

What is the stress area of an M20 × 2.5 bolt?

245 mm². An M12 × 1.75 is 84.3 mm² and an M30 × 3.5 is 561 mm².

Why not use the full shank area?

A bolt breaks in the thread. The stress area, between the pitch and minor diameters, is the area that tensile tests of threaded bolts fit best.

Does a fine thread have more stress area?

Yes. A finer pitch cuts less deep, so an M20 × 1.5 has more stress area than an M20 × 2.5.

Method and article reviewed by FireCAD engineering on 12 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.