FireCADCalc

Band Brake Torque and Lever Force

Braking torque of a simple band brake from the band tensions, friction and wrap angle (capstan equation), with the lever force for a given lever arrangement.

Inputs

Examples: 500 N·m, 250 mm drum, 270°, μ 0.3, 80/600 mm lever2 kN·m, 400 mm, 240°, μ 0.25, 100/900 mm80 N·m, 100 mm, 180°, μ 0.4, 40/300 mm

Results

Simple band brake with the tight end fixed at the pivot; reversing the drum swaps the ends and needs a much larger force.

Tension ratio e^{μθ}4.1112
Tight-side tension2.6428kN
Slack-side tension0.64284kN
Force at the lever end (simple band brake, tight end at the pivot)0.085712kN

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: 500 N·m, 250 mm drum, 270°, μ 0.3, 80/600 mm lever. The inputs, in the units selected above:

InputValue
Braking torque needed500.00 N·m
Drum radius250.00 mm
Coefficient of friction0.30000 -
Angle of wrap270.00 °
Distance from the lever pivot to the band's slack end80.000 mm
Lever length to the hand or actuator600.00 mm

Applying the formula below gives:

ResultValue
Tension ratio e^{μθ}4.1112
Tight-side tension2.6428 kN
Slack-side tension0.64284 kN
Force at the lever end (simple band brake, tight end at the pivot)0.085712 kN

Open this example in the calculator and change any input.

Formula

\(\frac{T_1}{T_2} = e^{\mu\theta}, \quad T = (T_1 - T_2) r, \quad P = T_2\, \frac{a}{l}\)

Variables

Symbol Meaning SI unit
\(T\) Braking torque needed N·m
\(r\) Drum radius m
\(\mu\) Coefficient of friction -
\(\theta\) Angle of wrap rad
\(a\) Distance from the lever pivot to the band's slack end m
\(l\) Lever length to the hand or actuator m
\(T_1/T_2\) Tension ratio e^{μθ} -
\(T_1\) Tight-side tension N
\(T_2\) Slack-side tension N
\(P\) Force at the lever end (simple band brake, tight end at the pivot) N

Method and standards

Capstan friction and lever moments.

Where it is used

  • Winches and hoists.
  • Machine design examinations.

Common mistakes

  • Wrap angle in degrees in the exponent.
  • Ignoring direction of rotation.

Assumptions and limits

  • Simple band brake, one drum direction (tight end at the pivot).
  • The band stress and the maximum lining pressure p_max = T₁/(b r) are not checked (the band width is not an input); check them for sizing.

References

  • Capstan equation applied to band brakes (Shigley's Mechanical Engineering Design (Budynas and Nisbett), ch. 16)

Questions and answers

500 N·m on a 250 mm radius drum, 270° wrap, μ 0.3?

T₁/T₂ = 4.11; T₂ = 643 N, T₁ = 2643 N.

What force at the lever?

86 N with 80 mm and 600 mm arms.

Why does direction matter?

With the drum reversed the tight side moves to the lever end.

Method and article reviewed by FireCAD engineering on 12 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.