Worked example
Example: Triple effect, 10 t/h from 5 % to 50 %, 2 bar(a) steam, 0.15 bar(a). The inputs, in the units selected above:
| Input | Value |
|---|---|
| Feed flow | 10.000 t/h |
| Solids in the feed | 5.0000 % |
| Solids in the product | 50.000 % |
| Number of effects | 3 |
| Heating steam pressure (absolute, saturated) | 2.0000 bar |
| Pressure in the last effect (absolute) | 0.15000 bar |
| Feed temperature | 60.000 °C |
| Specific heat of the liquor | 3.9000 kJ/(kg·K) |
Applying the formula below gives:
| Result | Value |
|---|---|
| Water evaporated | 9.0000 t/h |
| Heating steam needed | 3.5951 t/h |
| Steam economy (kg water per kg steam) | 2.5034 kg/kg |
| Vapour from the last effect to the condenser | 3.1187 t/h |
| Boiling temperature in the first effect | 98.131 °C |
Open this example in the calculator and change any input.
Formula
\(E = F \left(1 - \frac{x_f}{x_p}\right)\)
\(S\, h_{fg}(T_s) + F c_p (T_f - T_1) = V_1 h_{fg}(T_1)\)
\(V_{i-1} h_{fg}(T_{i-1}) + L_{i-1} c_p (T_{i-1} - T_i) = V_i h_{fg}(T_i)\)
\(\sum V_i = E\)
Variables
| Symbol | Meaning | SI unit |
|---|---|---|
| \(F\) | feed flow | kg/s |
| \(x_f\) | solids in the feed | - |
| \(x_p\) | solids in the product | - |
| \(N\) | number of effects | - |
| \(p_s\) | heating steam pressure | Pa |
| \(p_N\) | last-effect pressure | Pa |
| \(T_f\) | feed temperature | K |
| \(c_p\) | liquor specific heat | J/(kg·K) |
| \(T_s\) | heating steam saturation temperature | K |
| \(T_i\) | boiling temperature in effect i | K |
| \(T_1\) | boiling temperature in the first effect | K |
| \(h_{fg}\) | latent heat of water | J/kg |
| \(V_i\) | vapour from effect i | kg/s |
| \(L_i\) | liquor leaving effect i | kg/s |
| \(E\) | water evaporated | kg/s |
| \(S\) | heating steam | kg/s |
| \(E / S\) | steam economy | kg/kg |
| \(V_N\) | vapour to the condenser | kg/s |
Method and standards
Forward feed: liquor flows from the first to the last effect with the vapour. Boiling temperatures fall in equal steps from the steam to the last-effect saturation temperature; each effect is heated by the previous effect's vapour, condensing at its saturation temperature (latent heats from IAPWS-IF97). The balances are linear in the steam flow, which is solved so the total evaporation matches.
Where it is used
- Estimating steam demand for a sugar, dairy or effluent evaporator.
- Comparing the gain from adding an effect.
- Sizing the condenser for the last-effect vapour.
Common mistakes
- Ignoring boiling-point rise in strong liquors (it reduces the useful temperature drop).
- Using gauge pressure for the last effect: it is under vacuum, enter absolute.
- Forgetting that a cold feed costs extra steam in the first effect.
Assumptions and limits
- No boiling-point rise and no heat losses. For strong liquors (such as a 50 % solids product) the boiling-point rise eats into the temperature drops and the real economy is noticeably lower than shown.
- Equal temperature drops per effect; liquor specific heat constant.
- Forward feed; vapour bleeds to other users not included.
References
- Effect-by-effect energy balance
- IAPWS-IF97 latent heats
Questions and answers
What steam economy does a triple effect give?
About 2.5 kg of water evaporated per kg of steam in the example (10 t/h from 5 % to 50 %, steam at 2 bar(a), last effect 0.15 bar(a)).
Why is the economy below the number of effects?
Latent heat rises as pressure falls, the feed must be heated to boiling in the first effect, and each effect's vapour only just evaporates its own weight.
How much water must be evaporated?
E = F (1 − x_f/x_p): concentrating 10 t/h from 5 % to 50 % solids removes 9 t/h of water.
Method and article reviewed by FireCAD engineering on 12 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.