Worked example
Example: Three components, LK = 2. The inputs, in the units selected above:
| Input | Value |
|---|---|
| Feed condition q | 1.0000 - |
| Light key is component | 2 |
| α of component 1 (relative to any one reference component) | 4.0000 - |
| α of component 2 | 2.0000 - |
| α of component 3 | 1.0000 - |
| α of component 4 (0 = absent) | 0 - |
| Feed mole fraction of 1 | 20.000 % |
| Feed mole fraction of 2 | 40.000 % |
| Feed mole fraction of 3 | 40.000 % |
| Feed mole fraction of 4 | 0 % |
| Distillate mole fraction of 1 | 33.000 % |
| Distillate mole fraction of 2 | 65.000 % |
| Distillate mole fraction of 3 | 2.0000 % |
| Distillate mole fraction of 4 | 0 % |
Applying the formula below gives:
| Result | Value |
|---|---|
| Underwood root | 1.2835 |
| Minimum reflux ratio | 1.2297 |
Open this example in the calculator and change any input.
Formula
\(\sum_i \frac{\alpha_i z_i}{\alpha_i - \theta} = 1 - q, \quad R_{min} + 1 = \sum_i \frac{\alpha_i x_{D,i}}{\alpha_i - \theta}\)
Variables
| Symbol | Meaning | SI unit |
|---|---|---|
| \(q\) | Feed condition q | - |
| \(\text{LK}\) | Light key is component | - |
| \(\alpha_1\) | α of component 1 (relative to any one reference component) | - |
| \(\alpha_2\) | α of component 2 | - |
| \(\alpha_3\) | α of component 3 | - |
| \(\alpha_4\) | α of component 4 (0 = absent) | - |
| \(z_1\) | Feed mole fraction of 1 | - |
| \(z_2\) | Feed mole fraction of 2 | - |
| \(z_3\) | Feed mole fraction of 3 | - |
| \(z_4\) | Feed mole fraction of 4 | - |
| \(x_{D,1}\) | Distillate mole fraction of 1 | - |
| \(x_{D,2}\) | Distillate mole fraction of 2 | - |
| \(x_{D,3}\) | Distillate mole fraction of 3 | - |
| \(x_{D,4}\) | Distillate mole fraction of 4 | - |
| \(\theta\) | Underwood root | - |
| \(R_{min}\) | Minimum reflux ratio | - |
Method and standards
Underwood equations solved by bisection for the root between the keys.
Where it is used
- Short-cut multicomponent column design.
Common mistakes
- Using the wrong root.
- Distillate fractions not at minimum reflux.
Assumptions and limits
- Constant α and molar overflow.
- Volatilities may be relative to any one component (a value below 1 is allowed for components heavier than the reference), in falling order.
- Feed and distillate fractions within ±1 % of 1 are accepted as entered, without normalising.
- Both keys must be in the feed, and a root must be found between their volatilities.
References
- Perry's Chemical Engineers' Handbook
- 9th ed. (McGraw-Hill, 2019)
- sec. 13 (distillation)
- Underwood equations (13-37) and (13-38)
Questions and answers
Which root is used?
The one between the volatilities of the light and heavy keys.
Why must α be relative to one reference?
Underwood uses ratios; any common reference works, usually the heaviest component.
Why does Perry's ask for four decimals in θ?
α − θ can be small, so small errors in θ swing Rmin.
Method and article reviewed by FireCAD engineering on 13 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.