FireCADCalc

Steam Blowing: Disturbance (Cleaning Force) Factor

Disturbance factor of a steam blow, the ratio of ṁ²v during the blow to that at maximum continuous rating at the same point, with IF97 specific volumes.

Thermal power plantProcess steam and utilitiesSugar mill and cogenerationDistillery and ethanolIAPWS-IF97 (water and steam)BoilerSteam turbine

Inputs

Examples: Low pressure blowPuffing blowSaturated blow at 10 bar(a)

Results

A factor above 1 means the blow cleans harder than full-load operation will disturb; the target value is set by the turbine supplier.

Specific volume while blowing0.18658m³/kg
Specific volume at MCR0.050026m³/kg
Disturbance factor1.3427

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: Low pressure blow. The inputs, in the units selected above:

InputValue
Blowing steam flow60.000 t/h
Blowing pressure at the point (absolute)15.000 bar
Blowing temperature (superheated)350.00 °C
Blowing steamSuperheated, at the temperature above
MCR steam flow100.00 t/h
MCR pressure at the point (absolute)66.000 bar
MCR temperature485.00 °C

Applying the formula below gives:

ResultValue
Specific volume while blowing0.18658 m³/kg
Specific volume at MCR0.050026 m³/kg
Disturbance factor1.3427

Open this example in the calculator and change any input.

Formula

\(K = \frac{\dot m_b^2 v_b}{\dot m_{MCR}^2 v_{MCR}}\)

Variables

Symbol Meaning SI unit
\(\dot m_b\) Blowing steam flow kg/s
\(p_b\) Blowing pressure at the point (absolute) Pa
\(T_b\) Blowing temperature (superheated) K
\(\text{state}_b\) Blowing steam: superheated or dry saturated -
\(\dot m_{MCR}\) MCR steam flow kg/s
\(p_{MCR}\) MCR pressure at the point (absolute) Pa
\(T_{MCR}\) MCR temperature K
\(v_b\) Specific volume while blowing m³/kg
\(v_{MCR}\) Specific volume at MCR m³/kg
\(K\) Disturbance factor -

Method and standards

Ratio of the momentum flux (ṁ²v, proportional to the dynamic pressure in a given bore) during the blow to that at MCR at the same point, with IAPWS-IF97 specific volumes.

Where it is used

  • Commissioning steam blows.

Common mistakes

  • Comparing at different points in the line.

Assumptions and limits

  • Same location and bore.
  • Blowing steam superheated, or dry saturated when chosen; wet steam is not covered.

References

  • Disturbance factor K = (ṁ²v)_blow/(ṁ²v)_MCR (momentum flux ratio); specific volumes from IAPWS-IF97

Questions and answers

Why ṁ²v?

Dynamic pressure ρv²/2 scales with ṁ²v for a given bore: it is the force that lifts debris.

Why low pressure blows work?

Low-pressure steam has a large specific volume, so a smaller flow reaches the same factor.

Target?

Above 1, by a margin the turbine supplier sets; follow the supplier's requirement.

Method and article reviewed by FireCAD engineering on 13 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.