FireCADCalc

Flue Gas Water Dew Point

Temperature at which water vapour in flue gas starts to condense, from the moisture content or from the fuel analysis and excess air.

Thermal power plantProcess steam and utilitiesSugar mill and cogenerationRefinery and petrochemicalThermic fluid heatingPulp and paperASME PTC 4 (fired steam generators)IAPWS-IF97 (water and steam)BoilerBurner and furnaceStack and chimney

Inputs

Examples: Natural gas flue gas, 17.5 % H2O, 1 atmIndian coal, 25 % excess airBagasse 50 % moisture, 30 % excess airFuel oil, 15 % excess air, furnace at 1.05 bar

Absolute; atmospheric for most ducts and stacks.

Value entered

Ultimate analysis, as fired, by mass

Results

Water dew point46.409°C
Partial pressure of water vapour0.10312bar
Water vapour in wet flue gas used10.177%

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: Natural gas flue gas, 17.5 % H2O, 1 atm. The inputs, in the units selected above:

InputValue
Water vapour content fromValue entered
Water vapour in wet flue gas, by volume17.500 %
Carbon45.000 %
Hydrogen3.5000 %
Oxygen5.0000 %
Nitrogen1.0000 %
Sulphur0.50000 %
Ash35.000 %
Moisture10.000 %
Excess air25.000 %
Air humidity (kg water per kg dry air)0.013000 kg/kg
Flue gas pressure (absolute)1.0132 bar

Applying the formula below gives:

ResultValue
Water dew point57.480 °C
Partial pressure of water vapour0.17732 bar
Water vapour in wet flue gas used17.500 %

Open this example in the calculator and change any input.

Formula

\(p_{H_2O} = y_{H_2O}\,p \qquad T_{dp} = T_{sat}\!\left(p_{H_2O}\right)\)

When the content comes from the fuel, \(y_{H_2O}\) is the water vapour (from hydrogen, fuel moisture and air humidity) divided by the total wet flue gas, both in kmol per kg of fuel.

Variables

Symbol Meaning SI unit
\(\text{basis}\) water vapour content entered, or from the fuel –
\(y_{H_2O}\) water vapour in wet flue gas by volume, entered –
\(C\), \(H\), \(O\), \(N\), \(S\) carbon, hydrogen, oxygen, nitrogen, sulphur in the fuel as fired –
\(A\) ash –
\(M\) moisture –
\(EA\) excess air –
\(\omega\) air humidity, kg water per kg dry air kg/kg
\(p\) flue gas absolute pressure Pa
\(T_{dp}\) water dew point K
\(p_{H_2O}\) partial pressure of water vapour Pa
\(y\) water vapour fraction used –

Method and standards

Dalton's law of partial pressures for an ideal-gas mixture, and the saturation temperature at the partial pressure from the IAPWS-IF97 region 4 equation (FireCAD's own implementation). The water content from the fuel uses the exact-ratio combustion balance with ASME PTC 4-2013 air.

Where it is used

  • Setting the condensing limit for economisers.
  • Designing condensing economisers.
  • Plume and corrosion studies.

Common mistakes

  • Confusing water dew point with acid dew point.
  • Using dry gas composition.
  • Ignoring air humidity and fuel moisture.

Assumptions and limits

  • Ideal-gas mixture; the enhancement factor (below 0.5 % at atmospheric pressure) is neglected; above about 5 bar a warning appears.
  • A partial pressure below the triple point (dew point below 0 °C) is rejected; the frost point applies there.
  • Pure water: dissolved acids raise the actual condensation temperature (see the acid dew point).
  • Complete combustion; no water from atomising steam or soot blowing unless included in the content entered.

References

  • IAPWS R7-97(2012) IF97 (saturation)
  • ASME PTC 4-2013 (air composition)

Questions and answers

What is the water dew point of natural gas flue gas?

Natural gas flue gas holds about 17–18 % water vapour by volume. At 17.5 % and atmospheric pressure the partial pressure is 17.7 kPa and the dew point 57.5 °C; a condensing economiser must cool the gas below this.

Is the water dew point the same as the acid dew point?

No. Sulphuric acid condenses well above the water dew point, often at 110–150 °C for sulphur-bearing fuels. Use the acid dew point calculator for the cold-end metal temperature.

Why is bagasse flue gas dew point so high?

Bagasse is about half water. With 30 % excess air the flue gas holds 26.7 % water vapour, which gives a dew point of 66.8 °C.

Method and article reviewed by FireCAD engineering on 10 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.