FireCADCalc

Gas Composition: Volume % to Mass %

Converts a gas analysis by volume (mole) to mass fractions and gives the mixture molar mass.

Refinery and petrochemicalChemical and fertiliser

Inputs

Examples: Dry air (with argon)Wet flue gas, natural gas

Composition by volume

Results

Oxygen by mass23.143%
Nitrogen by mass75.514%
Carbon dioxide by mass0.060773%
Water vapour by mass0%
Sulphur dioxide by mass0%
Carbon monoxide by mass0%
Hydrogen by mass0%
Argon by mass1.2826%
Mixture molar mass28.966kg/kmol

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: Dry air (with argon). The inputs, in the units selected above:

InputValue
Oxygen (O2) by volume20.950 %
Nitrogen (N2) by volume78.080 %
Carbon dioxide (CO2) by volume0.040000 %
Water vapour (H2O) by volume0 %
Sulphur dioxide (SO2) by volume0 %
Carbon monoxide (CO) by volume0 %
Hydrogen (H2) by volume0 %
Argon (Ar) by volume0.93000 %

Applying the formula below gives:

ResultValue
Oxygen by mass23.143 %
Nitrogen by mass75.514 %
Carbon dioxide by mass0.060773 %
Water vapour by mass0 %
Sulphur dioxide by mass0 %
Carbon monoxide by mass0 %
Hydrogen by mass0 %
Argon by mass1.2826 %
Mixture molar mass28.966 kg/kmol

Open this example in the calculator and change any input.

Formula

\(M = \sum_i y_i M_i \qquad w_i = \frac{y_i\,M_i}{M}\)

Variables

Symbol Meaning SI unit
\(y_i\) mole (volume) fraction of species i: \(y_{O_2}\), \(y_{N_2}\), \(y_{CO_2}\), \(y_{H_2O}\), \(y_{SO_2}\), \(y_{CO}\), \(y_{H_2}\), \(y_{Ar}\) –
\(M_i\) molar mass of species i kg/kmol
\(M\) molar mass of the mixture kg/kmol
\(w_i\) mass fraction of species i: \(w_{O_2}\), \(w_{N_2}\), \(w_{CO_2}\), \(w_{H_2O}\), \(w_{SO_2}\), \(w_{CO}\), \(w_{H_2}\), \(w_{Ar}\) –

Method and standards

Molar masses are computed from the IUPAC 2013 conventional atomic weights (C 12.011, H 1.008, O 15.999, N 14.007, S 32.06, Ar 39.948 kg/kmol). The conversion is exact for ideal-gas mixtures.

Where it is used

  • Converting gas volumes to mass for balances.
  • Emission and fuel calculations.
  • Reading supplier data in volume units.

Common mistakes

  • Mixing normal and standard conditions.
  • Using actual volume with normal density.
  • Using the wrong molar mass for a mixture.

Assumptions and limits

  • Ideal gas: volume fraction equals mole fraction.
  • Only O₂, N₂, CO₂, H₂O, SO₂, CO, H₂ and Ar can be entered; hydrocarbons and H₂S of a fuel gas are not covered.
  • Fractions that do not sum to 1 are normalised; the page reports the original sum.

References

  • IUPAC 2013 standard atomic weights

Questions and answers

Are volume percent and mole percent the same?

For an ideal gas, yes (Avogadro's law). Flue gas at atmospheric pressure is close enough to ideal for ordinary analysis work.

My analysis does not add up to 100 %. What happens?

The calculator normalises the fractions to 100 % and tells you by how much they were off. Check for a missing component such as water vapour or nitrogen.

Method and article reviewed by FireCAD engineering on 10 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.