Worked example
Example: Indian coal, 5 % O2. The inputs, in the units selected above:
| Input | Value |
|---|---|
| O₂ in dry flue gas | 5.0000 % |
| Carbon | 45.000 % |
| Hydrogen | 3.5000 % |
| Oxygen | 5.0000 % |
| Nitrogen | 1.0000 % |
| Sulphur | 0.50000 % |
| Ash | 35.000 % |
| Moisture | 10.000 % |
Applying the formula below gives:
| Result | Value |
|---|---|
| CO₂ in dry flue gas | 13.793 % |
| Maximum CO₂ (stoichiometric) | 18.117 % |
| Excess air | 30.356 % |
Open this example in the calculator and change any input.
Formula
\(n_{O_2} = \frac{C}{M_C} + \frac{H}{2 M_{H_2}} + \frac{S}{M_S} - \frac{O}{M_{O_2}} \qquad n_a = \frac{n_{O_2}}{0.2095}\)
\(n_{d,0} = \frac{C}{M_C} + \frac{S}{M_S} + \frac{N}{M_{N_2}} + 0.7905\,n_a \qquad EA = \frac{O_2\,n_{d,0}}{n_a\,(0.2095 - O_2)}\)
\(CO_2 = \frac{C/M_C}{n_{d,0} + EA\,n_a} \qquad CO_{2,max} = \frac{C/M_C}{n_{d,0}}\)
Variables
| Symbol | Meaning | SI unit |
|---|---|---|
| \(O_2\) | O₂ in dry flue gas | – |
| \(C\), \(H\), \(O\), \(N\), \(S\), \(A\), \(M\) | ultimate analysis as fired, mass fractions (A and M only complete the 100 % check) | – |
| \(CO_2\) | CO₂ in dry flue gas | – |
| \(CO_{2,max}\) | maximum CO₂ (stoichiometric) | – |
| \(EA\) | excess air | – |
| \(n_{O_2}\) | oxygen needed per kg of fuel | kmol/kg |
| \(n_a\) | theoretical air per kg of fuel | kmol/kg |
| \(n_{d,0}\) | dry flue gas at zero excess air | kmol/kg |
| \(M_C\), \(M_{H_2}\), \(M_S\), \(M_{O_2}\), \(M_{N_2}\) | molar masses | kg/kmol |
Method and standards
Dry flue gas balance with air of 20.95 % O₂ and 79.05 % "atmospheric nitrogen" (N₂, Ar and CO₂ of air) as in ASME PTC 4; molar masses from IUPAC 2013 atomic weights.
Where it is used
- Converting old CO₂-based (Orsat) records to O₂.
- Checking two analysers against each other.
- Combustion tuning when only a CO₂ meter is fitted.
Common mistakes
- Comparing CO₂ readings between different fuels.
- Mixing wet and dry readings.
- Ignoring air leakage before the probe.
Assumptions and limits
- Complete combustion (no CO); dry basis; sulphur counted as SO₂ but not in the CO₂ reading; the 0.04 % CO₂ of the air is counted with the nitrogen.
- The analysis must sum to 100 %. Ash and moisture do not enter the dry gas balance: the result depends only on the ratios of C, H, O, N and S.
- An Orsat (KOH) reading absorbs CO₂ and SO₂ together; for a high-sulphur fuel compare it with CO₂ plus the SO₂ share.
References
- Combustion stoichiometry of the dry flue gas
- ASME PTC 4 air composition
Questions and answers
How is CO₂ related to O₂ in flue gas?
Both come from the same air and fuel balance. For coal with 45 % carbon at 5 % O₂ (30 % excess air), the dry flue gas holds 13.8 % CO₂; with no excess air it would hold the fuel's maximum, 18.1 %.
Why does CO₂ max depend on the fuel?
Fuels with more hydrogen form water, which leaves the dry gas, but also need more air per kg of carbon. Natural gas peaks near 12 %, oil near 15–16 %, coal near 18–19 %.
Should I control on O₂ or CO₂?
O₂: it depends little on the fuel, while the same CO₂ means different excess air for different fuels.
Method and article reviewed by FireCAD engineering on 11 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.