FireCADCalc

Excess Air from Flue Gas O₂, CO₂ and CO

Turns dry-basis analyser readings into excess air by the simple O₂ formula and by the ASME PTC 4 nitrogen balance with CO correction.

Thermal power plantProcess steam and utilitiesSugar mill and cogenerationRefinery and petrochemicalThermic fluid heatingPulp and paperASME PTC 4 (fired steam generators)Burner and furnaceStack and chimney

Inputs

Examples: Natural gas, 3 % O2Coal, 5 % O2High CO, 2.5 % O2

Dry basis, as the analyser reads it.
Dry basis. Enter 0 if CO₂ is not measured: only the simple O₂ method is then shown, because the nitrogen balance needs CO₂.

Results

CO above 1 000 ppm: combustion is incomplete; the PTC 4 value is the one to use.

Excess air, simple O₂ method13.550%
Excess air, PTC 4 nitrogen balance11.747%
Nitrogen in dry flue gas (by difference)85.250%
Air ratio λ = 1 + EA (PTC 4)1.1175

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: Natural gas, 3 % O2. The inputs, in the units selected above:

InputValue
Oxygen in dry flue gas3.0000 %
Carbon dioxide in dry flue gas (0 = not measured)10.500 %
Carbon monoxide in dry flue gas10.000 ppm

Applying the formula below gives:

ResultValue
Excess air, simple O₂ method16.713 %
Excess air, PTC 4 nitrogen balance15.054 %
Nitrogen in dry flue gas (by difference)86.499 %
Air ratio λ = 1 + EA (PTC 4)1.1505

Open this example in the calculator and change any input.

Formula

Simple oxygen method (complete combustion assumed):

\(EA_{O_2} = \frac{y_{O_2}}{0.2095 - y_{O_2}}\)

ASME PTC 4 nitrogen balance with CO correction:

\(y_{N_2} = 1 - y_{O_2} - y_{CO_2} - y_{CO} \qquad EA_{PTC4} = \frac{y_{O_2} - \tfrac{1}{2} y_{CO}}{\tfrac{0.2095}{0.7905}\, y_{N_2} - \left(y_{O_2} - \tfrac{1}{2} y_{CO}\right)} \qquad \lambda = 1 + EA_{PTC4}\)

Variables

Symbol Meaning SI unit
\(y_{O_2}\) oxygen in dry flue gas, volume fraction –
\(y_{CO_2}\) carbon dioxide in dry flue gas, volume fraction (0 = not measured) –
\(y_{CO}\) carbon monoxide in dry flue gas, volume fraction (1 ppm = 10⁻⁶) –
\(y_{N_2}\) nitrogen (with argon) in dry flue gas, by difference –
\(EA_{O_2}\) excess air fraction by the simple method –
\(EA_{PTC4}\) excess air fraction by the PTC 4 nitrogen balance –
\(\lambda\) air ratio, actual air over stoichiometric air –

Method and standards

Air is taken as 20.95 % O₂ and 79.05 % atmospheric nitrogen (N₂ + Ar) by volume, as in ASME PTC 4-2013. The nitrogen in the flue gas all came with the air (fuel nitrogen is neglected), so the air supplied is y_N₂ / 0.7905 and the oxygen that came with it is 0.2095/0.7905 · y_N₂. The oxygen left over, after crediting half a mole of O₂ per mole of CO that did not burn, divided by the oxygen consumed gives the excess air.

Where it is used

  • Turning dry-basis analyser readings into excess air for tuning and efficiency tests.
  • Comparing portable and fixed analysers.
  • Emission and efficiency reports.

Common mistakes

  • Mixing wet and dry readings.
  • Using a reading from a leaking sampling line.
  • Ignoring the analyser's measuring basis.

Assumptions and limits

  • Dry-basis readings; convert wet readings first.
  • Fuel nitrogen is neglected in the balance (it adds to the "air" nitrogen and makes the excess air read slightly high; negligible for gas and oil).
  • SO₂ and any other unmeasured species fall into the nitrogen by difference, slightly raising the PTC 4 value for high-sulphur fuels.
  • No wet/dry or reference-O₂ conversion is done here; use the emission O₂ correction calculator for those.
  • Undefined when O₂ reaches 20.95 % or when the readings leave no nitrogen.
  • CO₂ = 0 is taken as not measured: only the simple O₂ method is shown, since nitrogen by difference would then include the CO₂.

References

  • ASME PTC 4-2013 §5.11.4
  • U.S. Standard Atmosphere (20.95 % O₂)

Questions and answers

Why does 3 % O₂ mean about 17 % excess air?

Air is 20.95 % oxygen, so 3 % O₂ left in the dry flue gas means 3/(20.95 − 3) ≈ 0.167 of the stoichiometric air was surplus. Nitrogen dominates the gas, so a small O₂ change is a large excess-air change.

When do the two methods differ?

When CO is significant or the fuel carries much nitrogen or CO₂. The PTC 4 balance credits the oxygen that would have burned the CO and uses the measured nitrogen; the simple formula assumes complete combustion.

Is the reading wet or dry basis?

Most analysers condition the sample and read dry. If yours reads wet, convert first: y_dry = y_wet / (1 − y_H₂O).

Method and article reviewed by FireCAD engineering on 10 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.