FireCADCalc

Gas Meter Reading to Normal and Standard Volume

Converts an actual gas flow at line pressure and temperature to normal (0 °C, 1 atm) and standard (15 °C, 1 atm) volume with a compressibility factor.

Thermal power plantProcess steam and utilitiesSugar mill and cogenerationDistillery and ethanolRefinery and petrochemicalFuel oil and gas system

Inputs

Examples: Biogas 500 m3/h at 3 bar(a)Natural gas 10 bar(a)

Shown as gauge (bar g, kg/cm² g, psig); choose an absolute unit to enter absolute pressure. Using a gauge reading as absolute is the commonest error.
15 °C by default; some contracts use 20 °C or 60 °F (15.56 °C).
For wet biogas: the share of water vapour at the meter, to give dry normal volume.

Results

Normal flow (0 °C, 1 atm, dry if water vapour is entered)1,876.7Nm³/h
Standard flow (at the standard temperature, 1 atm)1,979.8m³/h
Correction factor to normal9.3836

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: Biogas 500 m3/h at 3 bar(a). The inputs, in the units selected above:

InputValue
Actual flow at the meter500.00 m³/h
Line pressure1.9868 bar g
Gas temperature30.000 °C
Compressibility factor0.99500 -
Standard reference temperature15.000 °C
Water vapour in the gas, by volume (0 = dry)0 %

Applying the formula below gives:

ResultValue
Normal flow (0 °C, 1 atm, dry if water vapour is entered)1,340.6 Nm³/h
Standard flow (at the standard temperature, 1 atm)1,414.2 m³/h
Correction factor to normal2.6812

Open this example in the calculator and change any input.

Formula

\(f = \frac{p}{p_n}\frac{T_n}{T}\frac{1 - y_w}{Z}, \quad \dot V_n = f\,\dot V, \quad \dot V_s = \dot V_n\,\frac{T_s}{T_n}\)

Variables

Symbol Meaning SI unit
\(\dot V\) Actual flow at the meter m³/s
\(p\) Line pressure (absolute) Pa
\(T\) Gas temperature K
\(Z\) Compressibility factor -
\(\dot V_n\) Normal flow (0 °C, 1 atm) Nm³/s
\(\dot V_s\) Standard flow (15 °C, 1 atm) m³/s
\(f\) Correction factor to normal -
\(p_n\), \(T_n\) normal pressure and temperature, 101.325 kPa and 273.15 K Pa, K
\(T_s\) standard reference temperature (15 °C default) K
\(y_w\) water vapour in the gas by volume (0 = dry) -

Method and standards

Real-gas law with a compressibility factor; the standard volume is at the reference temperature you choose and 1 atm.

Where it is used

  • Fuel gas billing checks.
  • Boiler fuel measurement.

Common mistakes

  • Gauge pressure used as absolute.

Assumptions and limits

  • Dry gas unless a water vapour share is entered, which is then removed from the normal and standard volumes.
  • The line pressure is shown as gauge by default; the calculation uses absolute pressure.
  • The standard pressure is 1 atm (101.325 kPa); a 60 °F contract at 14.73 psia differs by about 0.2 %.

References

  • Real-gas law V_n = V (p/p_n)(T_n/T)/Z

Questions and answers

Normal or standard?

Normal is 0 °C; standard is commonly 15 °C (some contracts use 20 °C or 60 °F): check the contract.

Compressibility?

Close to 1 at low pressure; matters at a few bar and above for natural gas.

Biogas?

Same correction; also remove the water vapour for dry volume.

Method and article reviewed by FireCAD engineering on 13 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.