Worked example
Example: Coal with 60 % C: 12 % CO₂, 7 % O₂, 0.5 % CO. The inputs, in the units selected above:
| Input | Value |
|---|---|
| Carbon in the fuel (burnt carbon, by mass) | 60.000 % |
| Carbon dioxide (dry, by volume) | 12.000 % |
| Oxygen (dry, by volume) | 7.0000 % |
| Carbon monoxide (dry, by volume) | 0.50000 % |
Applying the formula below gives:
| Result | Value |
|---|---|
| Dry flue gas per kg of fuel | 12.122 kg/kg |
| Dry flue gas per kg of fuel at 0 °C, 101.325 kPa | 8.9574 Nm³/kg |
| Air supplied per kg of fuel | 11.788 kg/kg |
| Share of the carbon burnt only to CO | 4.0000 % |
| Molar mass of the dry flue gas | 30.332 kg/kmol |
Open this example in the calculator and change any input.
Formula
\(n_{dg} = \frac{C / M_C}{CO_2 + CO}\)
\(m_{dg} = n_{dg} \sum y_i M_i, \quad V_{dg} = n_{dg}\, V_m\)
\(m_a = n_{dg}\, \frac{N_2}{0.7905}\, M_{air}\)
Variables
| Symbol | Meaning | SI unit |
|---|---|---|
| \(C\) | Carbon in the fuel (burnt carbon, by mass) | - |
| \(CO_2\) | Carbon dioxide (dry, by volume) | - |
| \(O_2\) | Oxygen (dry, by volume) | - |
| \(CO\) | Carbon monoxide (dry, by volume) | - |
| \(m_{dg}\) | Dry flue gas per kg of fuel | kg/kg |
| \(V_{dg}\) | Dry flue gas per kg of fuel at 0 °C, 101.325 kPa | m³/kg |
| \(m_a\) | Air supplied per kg of fuel | kg/kg |
| \(f_{CO}\) | Share of the carbon burnt only to CO | - |
| \(M_{dg}\) | Molar mass of the dry flue gas | kg/kmol |
| \(n_{dg}\) | dry flue gas per kg of fuel | kmol/kg |
| \(N_2\) | nitrogen by difference, \(1 - CO_2 - O_2 - CO\) | - |
| \(M_C\) | atomic mass of carbon, 12.011 | kg/kmol |
| \(y_i\), \(M_i\) | volume fractions and molar masses of CO₂, O₂, CO and atmospheric nitrogen | -, kg/kmol |
| \(V_m\) | molar volume at 0 °C, 101.325 kPa, 22.414 | m³/kmol |
| \(M_{air}\) | molar mass of dry air, 28.96 | kg/kmol |
Method and standards
Every kmol of carbon burnt makes one kmol of CO₂ + CO, which fixes the moles of dry gas; the nitrogen in it fixes the air supplied.
Worked example
Coal with 60 % carbon gives a flue gas of 12 % CO₂, 7 % O₂, 0.5 % CO, 80.5 % N₂ by volume.
- Textbook: (11 × 12 + 8 × 7 + 7 × (0.5 + 80.5)) / (3 × (12 + 0.5)) × 0.6 = 12.1 kg dry gas per kg of coal
- Air supplied: the 80.5 % nitrogen came with 11.8 kg of air per kg of coal
Where it is used
- Boiler attendant and operator examinations.
- Dry flue gas loss and fan duty from a flue gas test.
- Checking the air supply to a furnace.
Common mistakes
- Using total carbon when some is left unburnt in the ash.
- Using a wet analysis.
- Forgetting that sulphur also forms gas (small).
Assumptions and limits
- Fuel nitrogen and sulphur neglected. An Orsat absorbs SO₂ with the CO₂, and the air's own 0.04 % CO₂ is counted too, so the carbon-bearing moles are slightly overstated.
- The nitrogen by difference is given the molar mass of atmospheric nitrogen (N₂ with argon and air CO₂, 28.16 kg/kmol), not 28.01; the textbook form uses 28, so the two differ by under 1 %.
- Carbon entered is the carbon actually burnt.
References
- Carbon and nitrogen balances (textbook)
- IUPAC 2013 molar masses; ASME PTC 4-2013 air
Questions and answers
How much dry flue gas does coal with 60 % carbon make at 12 % CO₂, 7 % O₂, 0.5 % CO?
12.1 kg per kg of coal (8.96 Nm³/kg), with 11.8 kg of air supplied.
What is the textbook form?
Dry flue gas per kg = (11 CO₂ + 8 O₂ + 7 (CO + N₂)) / (3 (CO₂ + CO)) × C, from the molar masses 44, 32 and 28 over 12. The calculator uses exact molar masses.
Why is 4 % of the carbon shown as burnt to CO?
CO / (CO₂ + CO) = 0.5 / 12.5: that carbon released less than a third of its heat.
Method and article reviewed by FireCAD engineering on 12 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.