FireCADCalc

Combustion Air and Flue Gas without a Fuel Analysis

Dry and wet combustion air and flue gas mass flows from heat input, excess air and heating value by Ganapathy's MMBtu method (constant air per unit heat fired).

Thermal power plantProcess steam and utilitiesSugar mill and cogenerationChemical and fertiliserPulp and paperFood, dairy and textileBoilerBurner and furnaceFan and blower

Inputs

Examples: Ganapathy: 75 MMBtu/h gas, 10 % excess airGanapathy: coal 9500 Btu/lb, 25 %, humid air

Leave 0 for gas and oil. For solid fuels the ash leaves as solids, not gas.

Results

For a solid fuel, enter its ash so that it is not counted in the flue gas.

Theoretical dry air per unit heat326.74kg/GJ
Dry combustion air43.091t/h
Wet combustion air43.867t/h
Fuel4.7747t/h
Flue gas (wet air + fuel)48.642t/h
Wet air per kg fuel9.1875kg/kg

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: Ganapathy: 75 MMBtu/h gas, 10 % excess air. The inputs, in the units selected above:

InputValue
Heat input (HHV basis)21.980 MW
Fuel (Ganapathy Table 2.4: dry air per MMBtu fired, lb)Natural gas (730)
Excess air10.000 %
Fuel higher heating value46.520 MJ/kg
Air humidity (kg water per kg dry air)0 g/kg
Ash in the fuel, as fired (subtracted from the flue gas)0 %

Applying the formula below gives:

ResultValue
Theoretical dry air per unit heat313.84 kg/GJ
Dry combustion air27.318 t/h
Wet combustion air27.318 t/h
Fuel1.7010 t/h
Flue gas (wet air + fuel)29.019 t/h
Wet air per kg fuel16.060 kg/kg

Open this example in the calculator and change any input.

Formula

\(A_{SI} = A\ \mathrm{lb/MMBtu} \to \mathrm{kg/J}, \quad W_a = Q\,A_{SI}\,(1 + EA), \quad W_{aw} = W_a(1 + \omega), \quad W_f = \frac{Q}{HHV}\)

\(W_g = W_{aw} + W_f\,(1 - A_f), \quad \frac{W_{aw}}{W_f} = A_{SI}\,(1 + EA)(1 + \omega)\,HHV\)

Variables

Symbol Meaning SI unit
\(Q\) Heat input (HHV basis) W
\(A\) theoretical dry air per MMBtu fired for the fuel chosen (Ganapathy Table 2.4) lb/MMBtu
\(A_f\) ash in the fuel as fired -
\(EA\) Excess air -
\(HHV\) Fuel higher heating value J/kg
\(\omega\) Air humidity (kg water per kg dry air) kg/kg
\(A_{SI}\) Theoretical dry air per unit heat kg/J
\(W_a\) Dry combustion air kg/s
\(W_{aw}\) Wet combustion air kg/s
\(W_f\) Fuel kg/s
\(W_g\) Flue gas (wet air + fuel less ash) kg/s
\(W_{aw}/W_f\) Wet air per kg fuel kg/kg

Method and standards

Ganapathy's MMBtu method.

Where it is used

  • Fan and duct sizing.
  • Quick checks of boiler and heater data sheets.

Common mistakes

  • Using LHV heat input with A on HHV basis.
  • Forgetting air moisture.

Assumptions and limits

  • HHV basis. The ash entered is subtracted from the flue gas; leave it 0 for gas and oil.
  • The HHV entered is not checked against the fuel class chosen for \(A\); keep them consistent (a gas \(A\) with a coal HHV gives a wrong fuel flow).

References

  • Ganapathy
  • Steam Plant Calculations Manual
  • 2nd ed. (Marcel Dekker, 1993)
  • Q2.10 and Table 2.4 (combustion constant A)

Questions and answers

Why is air per unit heat nearly constant?

Heat release and oxygen demand both scale with carbon and hydrogen burnt; fossil fuels need 720–780 lb of air per MMBtu.

How accurate is it?

Good enough for fan and duct sizing, Ganapathy notes, when the fuel analysis is unknown.

What does A mean in SI?

730 lb/MMBtu natural gas is about 314 kg of air per GJ fired.

Method and article reviewed by FireCAD engineering on 13 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.