FireCADCalc

Dead Weight Safety Valve Load

Dead weight a safety valve needs to lift at a set pressure: the steam force on the valve area less the weight of the valve and its weight carrier.

Thermal power plantProcess steam and utilitiesSugar mill and cogenerationPulp and paperFood, dairy and textileBoilerBoiler attendant and boiler operator examinations

Inputs

Examples: 8 kg/cm² g, 50 mm, 5 kg valve3 bar g, 75 mm, 12 kg1 kg/cm² g, 100 mm, no carrier mass

Enter the gauge set pressure. An absolute value is turned to gauge with the standard atmosphere, which is wrong at altitude.

Results

Dead weight valves suit only low pressures and small valves: the weight grows with pressure × area.

Valve area78.540cm²
Steam force on the valve770.21N
Total mass to be lifted (F / g)78.540kg
Dead weight to add78.540kg

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: 8 kg/cm² g, 50 mm, 5 kg valve. The inputs, in the units selected above:

InputValue
Blow-off pressure7.8453 bar g
Valve diameter (area the steam acts on)50.000 mm
Mass of the valve and weight carrier5.0000 kg

Applying the formula below gives:

ResultValue
Valve area19.635 cm²
Steam force on the valve1,540.4 N
Total mass to be lifted (F / g)157.08 kg
Dead weight to add152.08 kg

Open this example in the calculator and change any input.

Formula

\(F = (p - p_{atm})\, \frac{\pi d^2}{4}\)

\(m_t = \frac{F}{g}, \quad m_d = m_t - m_v\)

Variables

Symbol Meaning SI unit
\(p\) Blow-off pressure Pa
\(d\) Valve diameter (area the steam acts on) m
\(m_v\) Mass of the valve and weight carrier kg
\(A\) Valve area m²
\(F\) Steam force on the valve N
\(m_t\) Total mass to be lifted (F / g) kg
\(m_d\) Dead weight to add kg

Method and standards

Force balance on the valve at the lift point.

Worked example

A dead weight safety valve of 50 mm diameter must blow at 8 kg/cm² g; the valve and carrier weigh 5 kg.

  • Area = π × 0.05²/4 = 19.63 cm²
  • Force = 8 kg/cm² × 19.63 cm² = 157.1 kgf (1540 N)
  • Dead weight = 157.1 − 5 = 152.1 kg

Where it is used

  • Boiler attendant examinations.
  • Low-pressure steam and hot-water vessels with weighted valves.

Common mistakes

  • Using absolute pressure.
  • Forgetting the valve's own weight.
  • Using kgf and N in the same sum.

Assumptions and limits

  • Static balance; friction neglected.
  • Principle calculation, not a code sizing: accumulation, overpressure and the difference between seat and bore area are not considered.
  • Gauge pressure is taken relative to the standard atmosphere; enter the gauge set pressure directly.

References

  • Force balance (statics, textbook)

Questions and answers

What dead weight does a 50 mm valve need at 8 kg/cm² g?

The steam force is 1540 N, which equals 157.1 kg; with a 5 kg valve and carrier, 152.1 kg of dead weight.

Why are dead weight valves only for small, low-pressure boilers?

The weight grows with pressure times area: a 100 mm valve at 10 kg/cm² g needs about 785 kg.

Is gauge or absolute pressure used?

Gauge: the atmosphere presses on both sides.

Method and article reviewed by FireCAD engineering on 12 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.